Smart Shower Control

Solenoid Valve

Power Supply 5V

Green LEDs

Hall effect flow sensor

Resistor 330 ohm

5V 1 Channel Relay Module

Active Buzzer 5V (HXD)

Arduino IDE

Power Supply 12V

Red LEDs

<html><body><h3>Arduino Smart Shower Management System</h3>The Smart Shower Management System is an Arduino control system designed for reducing water use and energy costs during showers. It turns off the hot water flow after a pre-set and configurable time. By limiting shower time, it ensures hot showers for everyone, while contributing for major water savings, depending on the current use. In the event of a power outage, both hot and cold water are able to flow, since the electrovalve should be a normally-open valve. <h3>1 - Components</h3>The components required for this project are the following (in parenthesis I state the models that I used in my implementation): <ol><li>Arduino (Arduino UNO) </li><li>Breadboard and cables </li><li>Relay: 1-channel low level trigger (TZT KY-019 5V) </li><li>2 LEDs (1 green, 1 red) </li><li>2 Resistors (with resistance $330\Omega$) </li><li>Buzzer (TMB09A03 active buzzer) </li><li>Hall-effect flow sensor (YF-B7 5VDC) </li><li>Normally-open solenoid valve (12VDC) </li><li>Dual Output Power Supply (5VDC and 12VDC) </li></ol> Note that the flow sensor and the solenoid valve must match your pipe diameter. <h3>2 - Installation &amp; Connections</h3>The high-level installation of the Smart Shower is highlighted in the figure below: <figure><img src="https://projects.arduinocontent.cc/9433a18c-f21d-4bc9-a30e-d73e26c6dd57.jpg"/><figcaption></figcaption></figure>More in particular, the Arduino connections the following: <ol><li>Flow Sensor is connected to digital input pin 2 (for external interrupt) </li><li>Red LED is connected to digital output pin 7 </li><li>Green LED is connected to digital output pin 5 </li><li>Buzzer is connected to digital output pin 6 </li><li>Relay is connected to digital output pin 11 </li></ol> The scheme is depicted in the following figure <figure><img src="https://projects.arduinocontent.cc/00878d8f-96ca-432f-a600-c073c0c5e956.png"/><figcaption></figcaption></figure> <h3>3 - Program Description</h3>The Arduino code implements a state machine controller. By measuring the flow at every second and monitoring the time, it controls the transitions between states and allows for a smart shower with 2 exit conditions (described below) The defined states are the following: <ol><li>State::IDLE </li><li>State::BATH </li><li>State::RECOVERY </li></ol> The following timing definitions are made: <ol><li>MAX_WATER_TIME - maximum water time during one bath cycle (defined in seconds) </li><li>MAX_BATH_LENGTH - maximum bath time (defined in seconds) </li><li>WARN_TIME - time to warn end of bath (defined in seconds) </li><li>RECOVERY_TIME - total time of the recovery state (defined in minutes) </li><li>TRANSITION_TIME - time to transition from IDLE state to BATH state (in seconds) </li></ol> Moreover, FLOW_THRESHOLD denotes flow-rate threshold to trigger transition from IDLE to BATH state. When the flow sensor readings are above FLOW_THRESHOLD , water is considered to be flowing. This threshold may be set to a certain positive number, in order to discard the processing of residual flow. Note that all these definitions can be easily tuned and upgraded to the Arduino board. <h3>3.1 - Program Flow</h3>The program starts in IDLE state and measures the flow rate with a frequency of 1Hz. If the flow at a given time is greater than FLOW_THRESHOLD, then it activates a transition flag. If after TRANSITION_TIME time, the flow is still greater than the threshold, then the program transitions to BATH state, otherwise it keeps in IDLE state. This is to prevent triggering a bath cycle for short periods of water use (which may be related to cleaning purposes, for example). When the program reaches the BATH state, it may transition to the RECOVERY state when one of two conditions is satisfied: <ol><li>The total bath time exceeds MAX_BATH_LENGTH </li><li>The total time that the flow sensor is measuring positive readings above the threshold (hot-water running) exceeds MAX_WATER_TIME </li></ol> Note that to get the total period of hot-water availability for a single shower, you also need to take into account the transition time from IDLE to BATH (specified by the TRANSITION_TIME constant). In any case, when the bath time is ending, the user is warned. During the last WARN_TIME seconds in the BATH state, the buzzer starts beeping and the green LED starts blinking. <h3>3.2 - Flowchart</h3>The program flow described above can be summarized in the following flowchart: <figure><img src="https://projects.arduinocontent.cc/86b42987-60a8-472f-9c10-38900a5bd471.jpg"/><figcaption></figcaption></figure> <h3>4 - User Configurations</h3> The parameters described above can be easily configured in `main.ino`. All the tunable parameters can be found inside the `USER DEFINITIONS` section placed at the beginning of the file. After making the intended changes, the program needs to be re-uploaded to the Arduino board. <h3>5 - My implementation</h3> Here you can see some photos of my implementation. I put the Arduino, the breadboard, the power supply and all the wires inside a protection box. I made 2 small holes in the box to place the LEDs and another one to place the buzzer. The solenoid valve and the flow sensor are then placed in hot-water pipe system, as shown in the bottom figure. <figure><img src="https://projects.arduinocontent.cc/cfc7e1ed-8231-4a9f-aa01-233b45acba15.jpg"/><figcaption></figcaption></figure> <figure><img src="https://projects.arduinocontent.cc/c757a4ba-c6c1-46de-9a4e-5697b706aa58.jpg"/><figcaption></figcaption></figure> <h3>6 - Contacts</h3> If you have any questions, doubts, or need further assistance regarding this Arduino project, feel free to contact me: Rodrigo Oliveira - Email: &lt;a href="mailto:rodrigo.moroliveira97@gmail.com"&gt;rodrigo.moroliveira97@gmail.com&lt;/a&gt; - GitHub: [https://github.com/rodrigo-moliveira] - LinkedIn [https://www.linkedin.com/in/rodrigo-moroliveira/] Please keep in mind that while I strive to provide support and assistance, I may not be able to respond immediately. Kindly allow for a reasonable amount of time for me to address your inquiries. Your feedback and suggestions for improving this Arduino project are also welcomed. If you encounter any issues or discover bugs, please consider opening an issue on the project's GitHub repository so that it can be tracked and addressed effectively. Thank you for your interest in this project, and I appreciate your understanding and cooperation in following the recommended communication channels outlined above. </body></html>

SmartShowerArduino