Sump Pit Alarm

Homegrown sump pit monitor with Nagios integration.

May 23, 2018

•

6985 views

•

12 respects

home automation

security

monitoring

Components and supplies

DHT22 Temperature Sensor

2" PVC pipe

Ultrasonic Sensor - HC-SR04 (Generic)

3 mm LED: Red

Buzzer

Arduino UNO

2" PVC pipe coupling

2" PVC pipe clean-out with lid

3 mm LED: Green

Tools and machines

Wire cutters/stripper

Soldering iron (generic)

Project description

Code

Nagios Plug-in

python

1#!/usr/bin/env python
2
3# $Rev::                         $:  Version  of last commit
4# $Author::                      $:  Author of last commit
5#  $Date::                                                $
6
7import serial
8import  re
9import sys
10
11try:
12    ser = serial.Serial('/dev/ttyACM0', 9600, timeout=15)
13    ser.close()
14    ser.open()
15
16    rawSensorOutput = ser.readline().rstrip('\n')
17
18    x = re.split('\\|', rawSensorOutput)
19
20    temp = float(x[0])
21    hum  = float(x[1])
22    dist = int(x[2])
23
24    if dist >= 31:
25        print  "SUMP PIT OK - %s cm from top; temp - %s, hum - %s" % (dist, temp, hum)
26        sys.exit(0)
27    elif dist <= 30:
28        print "SUMP PIT CRITICAL - %s cm from top; temp  - %s, hum - %s" % (dist, temp, hum)
29        sys.exit(2)
30    else:
31        print  "SUMP PIT UNKNOWN"
32        sys.exit(3)
33
34except (OSError, serial.SerialException):
35    print "SUMP PIT CRITICAL - Cannot open serial port"
36    sys.exit(2)

#!/usr/bin/env python

# $Rev::                         $:  Version  of last commit
# $Author::                      $:  Author of last commit
#  $Date::                                                $

import serial
import  re
import sys

try:
    ser = serial.Serial('/dev/ttyACM0', 9600, timeout=15)
    ser.close()
    ser.open()

    rawSensorOutput = ser.readline().rstrip('\n')

    x = re.split('\\|', rawSensorOutput)

    temp = float(x[0])
    hum  = float(x[1])
    dist = int(x[2])

    if dist >= 31:
        print  "SUMP PIT OK - %s cm from top; temp - %s, hum - %s" % (dist, temp, hum)
        sys.exit(0)
    elif dist <= 30:
        print "SUMP PIT CRITICAL - %s cm from top; temp  - %s, hum - %s" % (dist, temp, hum)
        sys.exit(2)
    else:
        print  "SUMP PIT UNKNOWN"
        sys.exit(3)

except (OSError, serial.SerialException):
    print "SUMP PIT CRITICAL - Cannot open serial port"
    sys.exit(2)

Pit Sensor Code

arduino

1// $Rev::                         $:  Version of last commit
2// $Author::                      $:  Author of last commit
3// $Date::                                                $
4
5#include  <DHT.h>;
6
7// DHT22 sensor setup
8#define DHTPIN 13
9#define DHTTYPE DHT22
10DHT  dht(DHTPIN, DHTTYPE);
11
12// pin setup
13const int trigPin = 7;
14const int  echoPin = 8;
15const int buzzerPin = 9;
16const int redLed = 11;
17const int  greenLed = 12;
18
19//Variables
20float hum;
21float temp;
22long duration;
23int  distance;
24
25void setup() {
26  // HC-SR04
27  pinMode(trigPin, OUTPUT); //  Sets the trigPin as an Output
28  pinMode(echoPin, INPUT); // Sets the echoPin  as an Input
29  // LEDs
30  pinMode(greenLed, OUTPUT);
31  pinMode(redLed, OUTPUT);
32  // Buzzer
33  pinMode(buzzerPin, OUTPUT);
34  //
35  Serial.begin(9600); //  Starts the serial communication
36  dht.begin();
37}
38
39void loop() {
40  // <---------------- HC-SR04 ------------------------->
41  // Clears the trigPin
42  digitalWrite(trigPin, LOW);
43  // 10000ms is 10 seconds
44  // 2000 ms is 2  seconds
45  delay(5000);
46  // Sets the trigPin on HIGH state for 10 micro seconds
47  digitalWrite(trigPin, HIGH);
48  delayMicroseconds(10);
49  digitalWrite(trigPin,  LOW);
50  // Reads the echoPin, returns the sound wave travel time in microseconds
51  duration = pulseIn(echoPin, HIGH);
52  // Calculating the distance in cm
53  distance = duration*0.034/2;
54
55  // <---------------- DHT22 ------------------------->
56  // Read data and store it to variables hum and temp
57  hum = dht.readHumidity();
58  temp = dht.readTemperature();
59  // Print temp and humidity values to serial  monitor
60  // Convert C to F
61  temp = temp * 9/5 + 32;
62  // Output
63  Serial.print(temp);
64  Serial.print("|");
65  Serial.print(hum);
66  Serial.print("|");
67  Serial.println(distance);
68
69  // <-------------- LEDs + buzzer ------------------------>
70  if (distance <=  20)
71    {
72      digitalWrite(redLed, HIGH);
73      digitalWrite(buzzerPin,  HIGH);
74      digitalWrite(greenLed, LOW);
75    }
76  else
77    {
78      digitalWrite(greenLed,  HIGH);
79      digitalWrite(redLed, LOW);
80      digitalWrite(buzzerPin, LOW);
81    }
82}

// $Rev::                         $:  Version of last commit
// $Author::                      $:  Author of last commit
// $Date::                                                $

#include  <DHT.h>;

// DHT22 sensor setup
#define DHTPIN 13
#define DHTTYPE DHT22
DHT  dht(DHTPIN, DHTTYPE);

// pin setup
const int trigPin = 7;
const int  echoPin = 8;
const int buzzerPin = 9;
const int redLed = 11;
const int  greenLed = 12;

//Variables
float hum;
float temp;
long duration;
int  distance;

void setup() {
  // HC-SR04
  pinMode(trigPin, OUTPUT); //  Sets the trigPin as an Output
  pinMode(echoPin, INPUT); // Sets the echoPin  as an Input
  // LEDs
  pinMode(greenLed, OUTPUT);
  pinMode(redLed, OUTPUT);
  // Buzzer
  pinMode(buzzerPin, OUTPUT);
  //
  Serial.begin(9600); //  Starts the serial communication
  dht.begin();
}

void loop() {
  // <---------------- HC-SR04 ------------------------->
  // Clears the trigPin
  digitalWrite(trigPin, LOW);
  // 10000ms is 10 seconds
  // 2000 ms is 2  seconds
  delay(5000);
  // Sets the trigPin on HIGH state for 10 micro seconds
  digitalWrite(trigPin, HIGH);
  delayMicroseconds(10);
  digitalWrite(trigPin,  LOW);
  // Reads the echoPin, returns the sound wave travel time in microseconds
  duration = pulseIn(echoPin, HIGH);
  // Calculating the distance in cm
  distance = duration*0.034/2;

  // <---------------- DHT22 ------------------------->
  // Read data and store it to variables hum and temp
  hum = dht.readHumidity();
  temp = dht.readTemperature();
  // Print temp and humidity values to serial  monitor
  // Convert C to F
  temp = temp * 9/5 + 32;
  // Output
  Serial.print(temp);
  Serial.print("|");
  Serial.print(hum);
  Serial.print("|");
  Serial.println(distance);

  // <-------------- LEDs + buzzer ------------------------>
  if (distance <=  20)
    {
      digitalWrite(redLed, HIGH);
      digitalWrite(buzzerPin,  HIGH);
      digitalWrite(greenLed, LOW);
    }
  else
    {
      digitalWrite(greenLed,  HIGH);
      digitalWrite(redLed, LOW);
      digitalWrite(buzzerPin, LOW);
    }
}

Nagios Plug-in

python

1#!/usr/bin/env python
2
3# $Rev::                         $:  Version
4  of last commit
5# $Author::                      $:  Author of last commit
6#
7  $Date::                                                $
8
9import serial
10import
11  re
12import sys
13
14try:
15    ser = serial.Serial('/dev/ttyACM0', 9600, timeout=15)
16
17    ser.close()
18    ser.open()
19
20    rawSensorOutput = ser.readline().rstrip('\
21')
22
23
24    x = re.split('\\|', rawSensorOutput)
25
26    temp = float(x[0])
27    hum
28  = float(x[1])
29    dist = int(x[2])
30
31    if dist >= 31:
32        print
33  "SUMP PIT OK - %s cm from top; temp - %s, hum - %s" % (dist, temp, hum)
34        sys.exit(0)
35
36    elif dist <= 30:
37        print "SUMP PIT CRITICAL - %s cm from top; temp
38  - %s, hum - %s" % (dist, temp, hum)
39        sys.exit(2)
40    else:
41        print
42  "SUMP PIT UNKNOWN"
43        sys.exit(3)
44
45except (OSError, serial.SerialException):
46
47    print "SUMP PIT CRITICAL - Cannot open serial port"
48    sys.exit(2)

#!/usr/bin/env python

# $Rev::                         $:  Version
  of last commit
# $Author::                      $:  Author of last commit
#
  $Date::                                                $

import serial
import
  re
import sys

try:
    ser = serial.Serial('/dev/ttyACM0', 9600, timeout=15)

    ser.close()
    ser.open()

    rawSensorOutput = ser.readline().rstrip('\
')


    x = re.split('\\|', rawSensorOutput)

    temp = float(x[0])
    hum
  = float(x[1])
    dist = int(x[2])

    if dist >= 31:
        print
  "SUMP PIT OK - %s cm from top; temp - %s, hum - %s" % (dist, temp, hum)
        sys.exit(0)

    elif dist <= 30:
        print "SUMP PIT CRITICAL - %s cm from top; temp
  - %s, hum - %s" % (dist, temp, hum)
        sys.exit(2)
    else:
        print
  "SUMP PIT UNKNOWN"
        sys.exit(3)

except (OSError, serial.SerialException):

    print "SUMP PIT CRITICAL - Cannot open serial port"
    sys.exit(2)

Downloadable files

Pit Sensor Diagram

Wiring connections are missing.

Pit Sensor Diagram

Wiring connections are missing.

Pit Sensor Diagram

Comments

Only logged in users can leave comments

loupalladino

0 Followers

•

0 Projects

Intro