IR Home Automation Using Arduino

Follow This Steps And Convert Your Home To Smart Home

Dec 29, 2017

•

1482 views

•

0 respects

smart appliances

Apps and platforms

Arduino IDE

Project description

Code

home automaton.ino

c_cpp

Final code of home automation and change the " #define code" in this program to your remort codes thanks for reading my story

1#include <IRremote.h>
2int RECV_PIN = 0; // the pin where you connect  the output pin of TSOP4838
3int led2 = 2;
4int led3 = 3;
5int led4 = 4;
6int  led5 = 5;
7int led6 = 6;
8int led7 = 7;
9int led8 = 8;
10int led9 = 9;
11int  led10 = 10;
12int led11 = 11;
13int led12 = 12;
14int itsONled[] = {0,0,0,0,0,0,0,0,0,0,0,0};
15/*  the initial state of LEDs is OFF (zero) 
16the first zero must remain zero but  you can 
17change the others to 1's if you want a certain
18led to light when  the board is powered */
19#define code2  16236607 // code received from button  A
20#define code3  16203967  // code received from button B
21#define code4  16220287
22#define  code5  16187647
23#define code6  16244767
24#define code7  16212127
25#define  code8  16228447
26#define code9  16195807
27#define code10 16208047
28#define  code11 16224367
29#define code12 16191727
30IRrecv irrecv(RECV_PIN);
31decode_results  results;
32void setup()
33{
34  Serial.begin(9600);   // you can comment this  line
35  irrecv.enableIRIn();  // Start the receiver
36  pinMode(led2,  OUTPUT);
37  pinMode(led3,  OUTPUT);
38  pinMode(led4,  OUTPUT);
39  pinMode(led5,  OUTPUT);
40  pinMode(led6,  OUTPUT);
41  pinMode(led7,  OUTPUT);
42  pinMode(led8,  OUTPUT);
43  pinMode(led9,  OUTPUT);
44  pinMode(led10, OUTPUT);
45  pinMode(led11, OUTPUT);
46  pinMode(led12, OUTPUT);
47}
48 void loop() {
49  if (irrecv.decode(&results))  {
50    unsigned int value = results.value;
51    switch(value) {
52       case  code2:
53         if(itsONled[2] == 1) {
54            digitalWrite(led2, LOW);
55            itsONled[2] = 0;
56         } else {
57             digitalWrite(led2,  HIGH);
58             itsONled[2] = 1;
59         }
60          break;
61       case  code3:
62         if(itsONled[3] == 1) {
63            digitalWrite(led3, LOW);
64            itsONled[3] = 0;
65         } else {
66             digitalWrite(led3,  HIGH);
67             itsONled[3] = 1;
68         }
69          break; 
70       case  code4:
71         if(itsONled[4] == 1) {
72            digitalWrite(led4, LOW);
73            itsONled[4] = 0;
74         } else {
75             digitalWrite(led4,  HIGH);
76             itsONled[4] = 1;
77         }
78          break;
79       case  code5:
80         if(itsONled[5] == 1) {
81            digitalWrite(led5, LOW);
82            itsONled[5] = 0;
83         } else {
84             digitalWrite(led5,  HIGH);
85             itsONled[5] = 1;
86         }
87          break; 
88       case  code6:
89         if(itsONled[6] == 1) {
90            digitalWrite(led6, LOW);
91            itsONled[6] = 0;
92         } else {
93             digitalWrite(led6,  HIGH);
94             itsONled[6] = 1;
95         }
96          break; 
97       case  code7:
98         if(itsONled[7] == 1) {
99            digitalWrite(led7, LOW);
100            itsONled[7] = 0;
101         } else {
102             digitalWrite(led7,  HIGH);
103             itsONled[7] = 1;
104         }
105          break; 
106       case  code8:
107          if(itsONled[8] == 1) {
108            digitalWrite(led8, LOW);
109            itsONled[8] = 0;
110         } else {
111             digitalWrite(led8,  HIGH);
112             itsONled[8] = 1;
113         }
114          break; 
115      case  code9:
116         if(itsONled[9] == 1) {
117            digitalWrite(led9, LOW);
118            itsONled[9] = 0;
119         } else {
120             digitalWrite(led9,  HIGH);
121             itsONled[9] = 1;
122         }
123          break;
124  case  code10:
125         if(itsONled[10] == 1) {
126            digitalWrite(led10, LOW);
127            itsONled[10] = 0;
128         } else {
129             digitalWrite(led10,  HIGH);
130             itsONled[10] = 1;
131         }
132          break; 
133  case code11:
134         if(itsONled[11] == 1) {
135            digitalWrite(led11,  LOW);
136            itsONled[11] = 0;
137         } else {
138             digitalWrite(led11,  HIGH);
139             itsONled[11] = 1;
140         }
141          break;
142  case  code12:
143         if(itsONled[12] == 1) {
144            digitalWrite(led12, LOW);
145            itsONled[12] = 0;
146         } else {
147             digitalWrite(led12,  HIGH);
148             itsONled[12] = 1;
149         }
150          break;    
151         }
152    Serial.println(value);
153    irrecv.resume(); // Receive the  next value
154  }
155}
156

#include <IRremote.h>
int RECV_PIN = 0; // the pin where you connect  the output pin of TSOP4838
int led2 = 2;
int led3 = 3;
int led4 = 4;
int  led5 = 5;
int led6 = 6;
int led7 = 7;
int led8 = 8;
int led9 = 9;
int  led10 = 10;
int led11 = 11;
int led12 = 12;
int itsONled[] = {0,0,0,0,0,0,0,0,0,0,0,0};
/*  the initial state of LEDs is OFF (zero) 
the first zero must remain zero but  you can 
change the others to 1's if you want a certain
led to light when  the board is powered */
#define code2  16236607 // code received from button  A
#define code3  16203967  // code received from button B
#define code4  16220287
#define  code5  16187647
#define code6  16244767
#define code7  16212127
#define  code8  16228447
#define code9  16195807
#define code10 16208047
#define  code11 16224367
#define code12 16191727
IRrecv irrecv(RECV_PIN);
decode_results  results;
void setup()
{
  Serial.begin(9600);   // you can comment this  line
  irrecv.enableIRIn();  // Start the receiver
  pinMode(led2,  OUTPUT);
  pinMode(led3,  OUTPUT);
  pinMode(led4,  OUTPUT);
  pinMode(led5,  OUTPUT);
  pinMode(led6,  OUTPUT);
  pinMode(led7,  OUTPUT);
  pinMode(led8,  OUTPUT);
  pinMode(led9,  OUTPUT);
  pinMode(led10, OUTPUT);
  pinMode(led11, OUTPUT);
  pinMode(led12, OUTPUT);
}
 void loop() {
  if (irrecv.decode(&results))  {
    unsigned int value = results.value;
    switch(value) {
       case  code2:
         if(itsONled[2] == 1) {
            digitalWrite(led2, LOW);
            itsONled[2] = 0;
         } else {
             digitalWrite(led2,  HIGH);
             itsONled[2] = 1;
         }
          break;
       case  code3:
         if(itsONled[3] == 1) {
            digitalWrite(led3, LOW);
            itsONled[3] = 0;
         } else {
             digitalWrite(led3,  HIGH);
             itsONled[3] = 1;
         }
          break; 
       case  code4:
         if(itsONled[4] == 1) {
            digitalWrite(led4, LOW);
            itsONled[4] = 0;
         } else {
             digitalWrite(led4,  HIGH);
             itsONled[4] = 1;
         }
          break;
       case  code5:
         if(itsONled[5] == 1) {
            digitalWrite(led5, LOW);
            itsONled[5] = 0;
         } else {
             digitalWrite(led5,  HIGH);
             itsONled[5] = 1;
         }
          break; 
       case  code6:
         if(itsONled[6] == 1) {
            digitalWrite(led6, LOW);
            itsONled[6] = 0;
         } else {
             digitalWrite(led6,  HIGH);
             itsONled[6] = 1;
         }
          break; 
       case  code7:
         if(itsONled[7] == 1) {
            digitalWrite(led7, LOW);
            itsONled[7] = 0;
         } else {
             digitalWrite(led7,  HIGH);
             itsONled[7] = 1;
         }
          break; 
       case  code8:
          if(itsONled[8] == 1) {
            digitalWrite(led8, LOW);
            itsONled[8] = 0;
         } else {
             digitalWrite(led8,  HIGH);
             itsONled[8] = 1;
         }
          break; 
      case  code9:
         if(itsONled[9] == 1) {
            digitalWrite(led9, LOW);
            itsONled[9] = 0;
         } else {
             digitalWrite(led9,  HIGH);
             itsONled[9] = 1;
         }
          break;
  case  code10:
         if(itsONled[10] == 1) {
            digitalWrite(led10, LOW);
            itsONled[10] = 0;
         } else {
             digitalWrite(led10,  HIGH);
             itsONled[10] = 1;
         }
          break; 
  case code11:
         if(itsONled[11] == 1) {
            digitalWrite(led11,  LOW);
            itsONled[11] = 0;
         } else {
             digitalWrite(led11,  HIGH);
             itsONled[11] = 1;
         }
          break;
  case  code12:
         if(itsONled[12] == 1) {
            digitalWrite(led12, LOW);
            itsONled[12] = 0;
         } else {
             digitalWrite(led12,  HIGH);
             itsONled[12] = 1;
         }
          break;    
         }
    Serial.println(value);
    irrecv.resume(); // Receive the  next value
  }
}

IR_CODE_DECO.ino

c_cpp

Remort IR code decorder or reader code of arduino

1
2#include <IRremote.h>
3
4int IRpin = 0;
5IRrecv irrecv(IRpin);
6decode_results   results;
7
8
9
10void setup()
11{
12  Serial.begin(9600);
13  irrecv.enableIRIn();   // Start the receiver
14}
15
16void loop() 
17{
18  if (irrecv.decode(&results))   
19    {
20      Serial.println(results.value, DEC); // Print the Serial 'results.value'
21       irrecv.resume();   // Receive the next value
22    }
23  
24  
25}
26
27

#include <IRremote.h>

int IRpin = 0;
IRrecv irrecv(IRpin);
decode_results   results;



void setup()
{
  Serial.begin(9600);
  irrecv.enableIRIn();   // Start the receiver
}

void loop() 
{
  if (irrecv.decode(&results))   
    {
      Serial.println(results.value, DEC); // Print the Serial 'results.value'
       irrecv.resume();   // Receive the next value
    }
  
  
}

IR_CODE_DECO.ino

c_cpp

Remort IR code decorder or reader code of arduino

1
2#include <IRremote.h>
3
4int IRpin = 0;
5IRrecv irrecv(IRpin);
6decode_results  results;
7
8
9
10void setup()
11{
12  Serial.begin(9600);
13  irrecv.enableIRIn();  // Start the receiver
14}
15
16void loop() 
17{
18  if (irrecv.decode(&results))  
19    {
20      Serial.println(results.value, DEC); // Print the Serial 'results.value'
21      irrecv.resume();   // Receive the next value
22    }
23  
24  
25}
26
27

#include <IRremote.h>

int IRpin = 0;
IRrecv irrecv(IRpin);
decode_results  results;



void setup()
{
  Serial.begin(9600);
  irrecv.enableIRIn();  // Start the receiver
}

void loop() 
{
  if (irrecv.decode(&results))  
    {
      Serial.println(results.value, DEC); // Print the Serial 'results.value'
      irrecv.resume();   // Receive the next value
    }
  
  
}

home automaton.ino

c_cpp

Final code of home automation and change the " #define code" in this program to your remort codes thanks for reading my story

1#include <IRremote.h>
2int RECV_PIN = 0; // the pin where you connect
3  the output pin of TSOP4838
4int led2 = 2;
5int led3 = 3;
6int led4 = 4;
7int
8  led5 = 5;
9int led6 = 6;
10int led7 = 7;
11int led8 = 8;
12int led9 = 9;
13int
14  led10 = 10;
15int led11 = 11;
16int led12 = 12;
17int itsONled[] = {0,0,0,0,0,0,0,0,0,0,0,0};
18/*
19  the initial state of LEDs is OFF (zero) 
20the first zero must remain zero but
21  you can 
22change the others to 1's if you want a certain
23led to light when
24  the board is powered */
25#define code2  16236607 // code received from button
26  A
27#define code3  16203967  // code received from button B
28#define code4  16220287
29#define
30  code5  16187647
31#define code6  16244767
32#define code7  16212127
33#define
34  code8  16228447
35#define code9  16195807
36#define code10 16208047
37#define
38  code11 16224367
39#define code12 16191727
40IRrecv irrecv(RECV_PIN);
41decode_results
42  results;
43void setup()
44{
45  Serial.begin(9600);   // you can comment this
46  line
47  irrecv.enableIRIn();  // Start the receiver
48  pinMode(led2,  OUTPUT);
49
50  pinMode(led3,  OUTPUT);
51  pinMode(led4,  OUTPUT);
52  pinMode(led5,  OUTPUT);
53
54  pinMode(led6,  OUTPUT);
55  pinMode(led7,  OUTPUT);
56  pinMode(led8,  OUTPUT);
57
58  pinMode(led9,  OUTPUT);
59  pinMode(led10, OUTPUT);
60  pinMode(led11, OUTPUT);
61
62  pinMode(led12, OUTPUT);
63}
64 void loop() {
65  if (irrecv.decode(&results))
66  {
67    unsigned int value = results.value;
68    switch(value) {
69       case
70  code2:
71         if(itsONled[2] == 1) {
72            digitalWrite(led2, LOW);
73
74            itsONled[2] = 0;
75         } else {
76             digitalWrite(led2,
77  HIGH);
78             itsONled[2] = 1;
79         }
80          break;
81       case
82  code3:
83         if(itsONled[3] == 1) {
84            digitalWrite(led3, LOW);
85
86            itsONled[3] = 0;
87         } else {
88             digitalWrite(led3,
89  HIGH);
90             itsONled[3] = 1;
91         }
92          break; 
93       case
94  code4:
95         if(itsONled[4] == 1) {
96            digitalWrite(led4, LOW);
97
98            itsONled[4] = 0;
99         } else {
100             digitalWrite(led4,
101  HIGH);
102             itsONled[4] = 1;
103         }
104          break;
105       case
106  code5:
107         if(itsONled[5] == 1) {
108            digitalWrite(led5, LOW);
109
110            itsONled[5] = 0;
111         } else {
112             digitalWrite(led5,
113  HIGH);
114             itsONled[5] = 1;
115         }
116          break; 
117       case
118  code6:
119         if(itsONled[6] == 1) {
120            digitalWrite(led6, LOW);
121
122            itsONled[6] = 0;
123         } else {
124             digitalWrite(led6,
125  HIGH);
126             itsONled[6] = 1;
127         }
128          break; 
129       case
130  code7:
131         if(itsONled[7] == 1) {
132            digitalWrite(led7, LOW);
133
134            itsONled[7] = 0;
135         } else {
136             digitalWrite(led7,
137  HIGH);
138             itsONled[7] = 1;
139         }
140          break; 
141       case
142  code8:
143          if(itsONled[8] == 1) {
144            digitalWrite(led8, LOW);
145
146            itsONled[8] = 0;
147         } else {
148             digitalWrite(led8,
149  HIGH);
150             itsONled[8] = 1;
151         }
152          break; 
153      case
154  code9:
155         if(itsONled[9] == 1) {
156            digitalWrite(led9, LOW);
157
158            itsONled[9] = 0;
159         } else {
160             digitalWrite(led9,
161  HIGH);
162             itsONled[9] = 1;
163         }
164          break;
165  case
166  code10:
167         if(itsONled[10] == 1) {
168            digitalWrite(led10, LOW);
169
170            itsONled[10] = 0;
171         } else {
172             digitalWrite(led10,
173  HIGH);
174             itsONled[10] = 1;
175         }
176          break; 
177
178  case code11:
179         if(itsONled[11] == 1) {
180            digitalWrite(led11,
181  LOW);
182            itsONled[11] = 0;
183         } else {
184             digitalWrite(led11,
185  HIGH);
186             itsONled[11] = 1;
187         }
188          break;
189  case
190  code12:
191         if(itsONled[12] == 1) {
192            digitalWrite(led12, LOW);
193
194            itsONled[12] = 0;
195         } else {
196             digitalWrite(led12,
197  HIGH);
198             itsONled[12] = 1;
199         }
200          break;    
201
202         }
203    Serial.println(value);
204    irrecv.resume(); // Receive the
205  next value
206  }
207}
208

#include <IRremote.h>
int RECV_PIN = 0; // the pin where you connect
  the output pin of TSOP4838
int led2 = 2;
int led3 = 3;
int led4 = 4;
int
  led5 = 5;
int led6 = 6;
int led7 = 7;
int led8 = 8;
int led9 = 9;
int
  led10 = 10;
int led11 = 11;
int led12 = 12;
int itsONled[] = {0,0,0,0,0,0,0,0,0,0,0,0};
/*
  the initial state of LEDs is OFF (zero) 
the first zero must remain zero but
  you can 
change the others to 1's if you want a certain
led to light when
  the board is powered */
#define code2  16236607 // code received from button
  A
#define code3  16203967  // code received from button B
#define code4  16220287
#define
  code5  16187647
#define code6  16244767
#define code7  16212127
#define
  code8  16228447
#define code9  16195807
#define code10 16208047
#define
  code11 16224367
#define code12 16191727
IRrecv irrecv(RECV_PIN);
decode_results
  results;
void setup()
{
  Serial.begin(9600);   // you can comment this
  line
  irrecv.enableIRIn();  // Start the receiver
  pinMode(led2,  OUTPUT);

  pinMode(led3,  OUTPUT);
  pinMode(led4,  OUTPUT);
  pinMode(led5,  OUTPUT);

  pinMode(led6,  OUTPUT);
  pinMode(led7,  OUTPUT);
  pinMode(led8,  OUTPUT);

  pinMode(led9,  OUTPUT);
  pinMode(led10, OUTPUT);
  pinMode(led11, OUTPUT);

  pinMode(led12, OUTPUT);
}
 void loop() {
  if (irrecv.decode(&results))
  {
    unsigned int value = results.value;
    switch(value) {
       case
  code2:
         if(itsONled[2] == 1) {
            digitalWrite(led2, LOW);

            itsONled[2] = 0;
         } else {
             digitalWrite(led2,
  HIGH);
             itsONled[2] = 1;
         }
          break;
       case
  code3:
         if(itsONled[3] == 1) {
            digitalWrite(led3, LOW);

            itsONled[3] = 0;
         } else {
             digitalWrite(led3,
  HIGH);
             itsONled[3] = 1;
         }
          break; 
       case
  code4:
         if(itsONled[4] == 1) {
            digitalWrite(led4, LOW);

            itsONled[4] = 0;
         } else {
             digitalWrite(led4,
  HIGH);
             itsONled[4] = 1;
         }
          break;
       case
  code5:
         if(itsONled[5] == 1) {
            digitalWrite(led5, LOW);

            itsONled[5] = 0;
         } else {
             digitalWrite(led5,
  HIGH);
             itsONled[5] = 1;
         }
          break; 
       case
  code6:
         if(itsONled[6] == 1) {
            digitalWrite(led6, LOW);

            itsONled[6] = 0;
         } else {
             digitalWrite(led6,
  HIGH);
             itsONled[6] = 1;
         }
          break; 
       case
  code7:
         if(itsONled[7] == 1) {
            digitalWrite(led7, LOW);

            itsONled[7] = 0;
         } else {
             digitalWrite(led7,
  HIGH);
             itsONled[7] = 1;
         }
          break; 
       case
  code8:
          if(itsONled[8] == 1) {
            digitalWrite(led8, LOW);

            itsONled[8] = 0;
         } else {
             digitalWrite(led8,
  HIGH);
             itsONled[8] = 1;
         }
          break; 
      case
  code9:
         if(itsONled[9] == 1) {
            digitalWrite(led9, LOW);

            itsONled[9] = 0;
         } else {
             digitalWrite(led9,
  HIGH);
             itsONled[9] = 1;
         }
          break;
  case
  code10:
         if(itsONled[10] == 1) {
            digitalWrite(led10, LOW);

            itsONled[10] = 0;
         } else {
             digitalWrite(led10,
  HIGH);
             itsONled[10] = 1;
         }
          break; 

  case code11:
         if(itsONled[11] == 1) {
            digitalWrite(led11,
  LOW);
            itsONled[11] = 0;
         } else {
             digitalWrite(led11,
  HIGH);
             itsONled[11] = 1;
         }
          break;
  case
  code12:
         if(itsONled[12] == 1) {
            digitalWrite(led12, LOW);

            itsONled[12] = 0;
         } else {
             digitalWrite(led12,
  HIGH);
             itsONled[12] = 1;
         }
          break;    

         }
    Serial.println(value);
    irrecv.resume(); // Receive the
  next value
  }
}

Downloadable files

Make 12 V to 5 V Converter Circuit

Component List 1 multipurpose circuit bord 2 capacitor 470uf ,1uf 3 diode in4007 4 ic LM7805 5 transistor bc547 6 relay 5v 7 arduino uno 8 any remort 9 tsop 1738

Make 12 V to 5 V Converter Circuit

Component List 1 multipurpose circuit bord 2 capacitor 470uf ,1uf 3 diode in4007 4 ic LM7805 5 transistor bc547 6 relay 5v 7 arduino uno 8 any remort 9 tsop 1738

Make 12 V to 5 V Converter Circuit

Documentation

Downlod IR Decord.ino File From Here

IR DECORD.INO Use arduino ide softwere open ir decorc.ino and upload to bord if you have any error like (C:\Program Files (x86)\Arduino\libraries\RobotIRremote\src\IRremoteTools.cpp:5: error: 'TKD2' was not declared in this scope) so downlod ir Library from here http://sh.st/J8DWM and extrect and past to C:\Program Files\Arduino\libraries after problem not solve downlod this libraries http://sh.st/J8Gf5 and past on same path

Downlod IR Decord.ino File From Here

Download Final Home Automation.ino

home automation.ino Downlod code and upload to bord change define code to your remort code

Download Final Home Automation.ino

Joint This Circuit for Use Reley (make Your Own Relay Bord for On/off Home Application)

Open Seriel Moniter(ctrl+shift+M)

press button from remort and note down received code like 16220287 16187647 16244767 16195807 16228447 Note down same code recived from pressing one button

Open Seriel Moniter(ctrl+shift+M)

Download Final Home Automation.ino

home automation.ino Downlod code and upload to bord change define code to your remort code

Download Final Home Automation.ino

Connect of TSOP 1738 to Arduino

Connect tsop1738 ground to arduino ground ,+5v to arduino +5v ,output to arduino 0 number in (RX)

Connect of TSOP 1738 to Arduino

Open Seriel Moniter(ctrl+shift+M)

press button from remort and note down received code like 16220287 16187647 16244767 16195807 16228447 Note down same code recived from pressing one button

Open Seriel Moniter(ctrl+shift+M)

Joint This Circuit for Use Reley (make Your Own Relay Bord for On/off Home Application)

Connect of TSOP 1738 to Arduino

Connect tsop1738 ground to arduino ground ,+5v to arduino +5v ,output to arduino 0 number in (RX)

Connect of TSOP 1738 to Arduino

Comments

Only logged in users can leave comments

jaypatel0532

0 Followers

•

0 Projects

Intro

Trademarks & CopyrightsWhistleblowingDigital Services ActTerms of ServicePrivacy PolicySecurityCookie Settings

Report content