1-Channel Relay Module and Air Valve

Arduino IDE

<p >*******</p><p ><span >Please visit </span><a href="https://proteshea.com/control-air-valve-with-relay-and-arduino-uno/">https://proteshea.com/control-air-valve-with-relay-and-arduino-uno/</a><span > for a complete list of materials needed for this project.</span></p><p >*******</p><h3 >Introduction</h3><p ><span >If you haven’t read our </span><a href="https://proteshea.com/arduino-uno-rev3-quick-start-guide/">Getting Started Guide </a><span >for the Arduino Uno Rev3 (Uno), please read that first. In this project, we’ll be connecting a 1-channel relay module to the Uno to control an electric solenoid air valve. The reason why we need a relay module is because the valve pulls 500 mA at +12Vdc – the Uno cannot source that much current (only 40 mA max), nor does it have a +12V rail. The air valve is not used in a complete pneumatic system as this tutorial is mainly about how to use a relay module to control a high-current load (a load in which the Uno cannot drive).</span></p><div class="se-component se-video-container __se__float-none" contenteditable="false" style="width: 100%;"><figure style="width: 100%; height: 56.25%; padding-bottom: 56.25%; margin: 0px;"><iframe frameborder="0" allowfullscreen="" src="https://www.youtube.com/embed/pK87UVWyzMY" data-proportion="true" data-percentage="100%,56.25%" data-size="100%,56.25%" data-align="none" style="width: 100%; height: 100%;" data-index="0" data-file-size="0" data-origin="100%,56.25%"></iframe></figure></div><h3 >Relay Module</h3><p >The relay module we’re using is 1-channel. There are other options such as a 2-channel relay which consists of two 1-channel relays on a single PCB. There are two sides on the relay: one that contains a 3-pin terminal block and one that contains a 3-pin male header as shown below. The terminal block is used to connect the high-power load and the 3-pin male header is used to connect to the Uno.</p><figure><img src=https://projects.arduinocontent.cc/3f140386-9e8c-4fe7-a503-f34b5bbda2e8.png /><figcaption>Relay Connections</figcaption></figure><p >First, we’ll explain the 3-pin terminal block. The 3 pins from left to right are normally closed (NC), common (COM), and normally open (NO). The pin assignments may vary from relay to relay, but you can quickly determine which pins are NO or NC. To do so, set your voltmeter to do a continuity check. Place one probe on the middle-pin block and the other probe on the left-pin block. If there is continuity, the left pin is NC. If not, the left pin is NO. The pin assignments for the terminal block that we’re using are shown below.</p><figure><img src=https://projects.arduinocontent.cc/76bfada5-3ea9-48d1-9ce4-1ecaaa974781.png /><figcaption>Terminal Block Pin Assignments</figcaption></figure><p >Next, we have the 3-pin right-angle male header which is used to connect to the Uno. The pins are labeled as “+”, “-“, and “S” which are shown below. We need to connect “-” pin to GND, the “+” pin to +5Vdc, and “S” to any of the Uno’s digital I/O pins – we connected it to pin 8.</p><figure><img src=https://projects.arduinocontent.cc/cb64aaa2-24c9-4805-ac46-51b88ead6136.png /><figcaption>Male Header Pin Assignments</figcaption></figure><h3 >Electric Solenoid Air Valve</h3><p >The air valve contains a solenoid to control the opening and closing of the valve. A solenoid consists of a coil of wire and when a current passes through the coil, a magnetic field is induced. This magnetic field causes the shaft to move inside of the coil. When the solenoid is energized, the shaft moves up causing the valve to open. When the solenoid is de-energized, the shaft moves back down causing the valve to close.</p><p >The ignition on a vehicle or outboard motor uses a solenoid to start the engine. When you turn the key, a current is sent through the coil of the solenoid which causes the rod to engage and turn the flywheel. Once the engine starts, the solenoid is de-energized and the rod disengages the flywheel. </p><p >The air valve has an inlet valve and an outlet valve and the direction of the air flow is on the valve so you can easily identify it. Each side contains a 1/4″ NPT threads which is common for pneumatic systems such as an air compressor. We used a 1/4″ x 1/4″ male NPT plug for the inlet side to connect an air hose and kept the outlet side as is. An image is shown below.</p><figure><img src=https://projects.arduinocontent.cc/10e13d0e-5343-4856-a124-09d6c83a8f07.png /><figcaption>Air Valve with Male NPT Plug Screwed In</figcaption></figure><h3 >Modulus</h3><p ><span >We are using Modulus to mount the relay to. If you have not soldered on anything to your Modulus Canister, please watch </span><a href="https://www.youtube.com/watch?v=x7Fe7-Hvp58&t=11s">this video </a><span >on our basic layout. We will be inserting the relay into the right-angle female header which is soldered to the 1-to-1 link. Then, we’ll wire wrap the – and + pins to GND and +5Vdc on Modulus, respectively. Please consult the FuelCan User Guide to determine the pinout of the 4×26-pin connector. We’ll use an 8″ F/M jumper to route the S pin of the relay to pin 8 on the Uno. An image is shown below with our setup.</span></p><figure><img src=https://projects.arduinocontent.cc/cad4e212-c6e8-4e22-9f86-c2539bedbcc0.jpg /><figcaption>Connecting the Relay to Modulus</figcaption></figure><h3 >Air Valve Wiring</h3><p ><span >Okay, we have one side of the relay connected. We now have to connect the air valve to the relay’s terminal block. The air valve requires +12Vdc and 500 mA which can be supplied by the FuelCan’s +12Vdc rail. The red wire will connect to the COM pin on the relay’s terminal block and the black wire will be connected to GND. An image is below for reference. Cut a 2″ piece of 20 AWG wire and strip 1/4″ of insulation off of both ends. Unscrew the NC terminal with a small flathead screwdriver and insert the 2″ piece of wire. Screw the terminal block screw back down to clamp the wire in. </span><strong >Make sure that you clamp down on the wire and not the insulation</strong><span >. Next, unscrew the COM terminal block screw, insert the red wire of the air valve, and clamp the wire into place.</span></p><p >Insert one of the banana cables into the +12Vdc female banana jack on the FuelCan and attach the test-lead clip to the 2″ piece of wire that is sticking out of the NC terminal block. Insert another banana cable into the GND female banana jack on the FuelCan and attach the test-lead clip to the black wire of the air valve.</p><figure><img src=https://projects.arduinocontent.cc/d32892e8-3fae-4b32-ae6f-ecd93dc74211.png /><figcaption>Wiring the Air Valve and 1-Channel Relay</figcaption></figure><h3 >FuelCan Wiring</h3><p >If you haven’t mounted the Uno onto the prototyping area of the FuelCan, go ahead and do that. Plug the Type A side of the USB cable into USB1 receptacle and the Type B side into the Uno’s receptacle. Plug the Type A to Type A USB cable into a USB port on your computer and the external USB connector of the FuelCan. Power up the FuelCan with the AC-DC power adapter.</p><p >The last thing to do besides the software is to attach the air hose to the air valve. Set the regulator on the air compressor to 115 PSI. If you go above this, you could damage the air valve. Go ahead and turn the air compressor on while we load the software.</p><h3 >Software</h3><p >Once the wiring is complete and the FuelCan is powered up, we can now load the sketch onto the Uno. The sketch is below. The air valve will open every 3 seconds and then close immediately.</p>

1-Channel Relay Module and Air Valve

Connect a 1-channel relay module to control an electric solenoid air valve.