LED HOURGLASS USING ARDUINO

Soldering Station

Arduino Nano

tinkercad

SparkFun Triple Axis Accelerometer Breakout - ADXL335

Arduino IDE

MAX7219 8x8 LED matrix

Arduino® Nano R4

<html><body>In ancient times, people relied on an hourglass as a simple yet effective tool to measure the passage of time. The hourglass is made up of two glass bulbs connected by a narrow neck, through which sand flows steadily from the upper bulb to the lower one. The duration of the sand flow was usually fixed—often about an hour—which is why it came to be known as the hourglass. This timeless device symbolises the continuous flow of time, and even today it is admired for its simplicity and elegance. Inspired by this traditional concept, in this tutorial, we will recreate the same idea in a modern way by building a digital hourglass using Arduino, where electronic components will replace sand and glass to simulate the passage of time in a creative and interactive form. <figure><iframe src="https://youtu.be/23EBLhm-rG8"></iframe></figure>COMPONENTS NEEDED <div id="gallery"><img id="gallery" src="https://projects.arduinocontent.cc/e448e46a-58c2-4498-ae5b-4e31eefce50f.jpg"/><figcaption></figcaption>,<img id="gallery" src="https://projects.arduinocontent.cc/20c42e14-2ba1-4703-98e5-dd2bad16c6b2.jpg"/><figcaption></figcaption></div> <ol><li>Arduino (Uno / Nano / Pro Mini) — 1 </li><li>ADXL335 breakout board — 1 </li><li>8×8 LED matrix + MAX7219 module — 2 </li><li>3.7V Li-ion battery — 1 </li><li>Charger+Booster Module — 1 </li><li>button switch – 1 </li><li>Wires </li><li>3D printed frame parts </li></ol>Arduino (the brain) The Arduino is the central controller for the digital hourglass: it reads the accelerometer, runs the “sand” animation, and talks to the LED drivers. I chose Arduino because it provides plenty of digital I/O, easy-to-use libraries, simple power and USB programming, and a huge community — perfect for a beginner-to-intermediate build. You can use an Uno, Nano, or a Pro Mini. ADXL335 3-axis analog accelerometer (orientation sensor) The ADXL335 gives you raw X, Y and Z analog voltages that correspond to the sensor’s orientation. For a digital hourglass, we just need to know which side is “up,” so the ADXL335 is a simple, low-cost choice that’s easy to read with analogRead() (No I²C required). It’s also tolerant of hobby-level wiring and works well mounted directly to the frame. Two 8×8 LED matrices driven by MAX7219 (the sand displays) To represent sand visually, we’ll use two 8×8 LED matrices — one representing the top bulb and one for the bottom. Each matrix is driven by a MAX7219 IC, so we only need three control pins (DIN, CLK, CS/LOAD) to control each module and can also daisy-chain them (data out of the first into the second). The MAX7219 handles multiplexing and brightness control for you, so you get crisp animations without manually time-multiplexing rows. You can animate falling grains by lighting pixels, moving them downward over time, and using the MAX7219 intensity register to tweak the visual “weight” of the sand. 3.7V Li-ion battery charger + 5V booster A single-cell 3.7V Li-ion battery charger+ booster is a compact choice. Because the Arduino + MAX7219s usually want 5V. So we charge the battery and boost the voltage to 5v with the same module, such this way we can decrease the size How the parts work together (conceptual) The ADXL335 senses which bulb is currently “up.” The Arduino reads the accelerometer, decides which matrix is the top and which is the bottom, and starts the sand animation accordingly. The MAX7219s receive frame data from the Arduino and show falling pixels. When you flip the hourglass, the Arduino detects the orientation change and reverses the animation, simulating sand moving from the new top matrix into the bottom matrix until one empties and the other fills. CIRCUIT DIAGRAM <figure><img src="https://projects.arduinocontent.cc/0dc48523-60db-4d47-af19-3cbde83c077e.jpg"/><figcaption></figcaption></figure>Arduino → MAX7219 (first LED Matrix) DIN → D5 CLK → D4 CS/LOAD → D6 VCC → 5V GND → GND MAX7219 (first Matrix) → MAX7219 (second Matrix) DOUT → DIN of second matrix CLK → CLK CS/LOAD → CS/LOAD VCC → VCC GND → GND ADXL335 → Arduino X → A1 Y → A2 VCC → 5V GND → GND You can download the circuit diagram from <a href="https://github.com/EDISON-SCIENCE-CORNER/LED-HOUR-GLASS">here </a>SOLDERING <div id="gallery"><img id="gallery" src="https://projects.arduinocontent.cc/0b7b6b02-5b21-4888-af1f-79fded7a866e.jpg"/><figcaption></figcaption>,<img id="gallery" src="https://projects.arduinocontent.cc/cb6fc614-af19-4dd0-90e2-792eb61379cf.jpg"/><figcaption></figcaption>,<img id="gallery" src="https://projects.arduinocontent.cc/533bf8a8-63a5-44e0-898e-28c394de94af.jpg"/><figcaption></figcaption></div> I soldered the X and Y output pins of the ADXL335 accelerometer to the A1 and A2 analog pins of the Arduino Nano, while the VCC and GND pins of the sensor were connected to the 5V and GND pins of the Nano. The two 8×8 LED matrices with MAX7219 drivers were daisy-chained together, and I soldered their DIN, CLK, and CS pins to the Nano’s D5, D4, and D6 digital pins, respectively, along with their VCC and GND lines to 5V and GND. For the power supply, I connected a 3.7V Li-Po battery to the IP5306 base booster and charging module, and from there soldered the 5V and GND output pins of the module to the Arduino Nano to power the entire circuit. 3D printed Encloure <div id="gallery"><img id="gallery" src="https://projects.arduinocontent.cc/dc6a65ec-8efa-4512-9c20-9484bcf00c82.png"/><figcaption></figcaption></div> I designed the enclosure using tinkercad and printed the files using my BambuLab A1 printer with PLA. You can download the files from <a href="https://github.com/EDISON-SCIENCE-CORNER/LED-HOUR-GLASS">here </a>Arduino Programming You can download the code from <a href="https://github.com/EDISON-SCIENCE-CORNER/LED-HOUR-GLASS">here </a> ASSEMBLY <div id="gallery"><img id="gallery" src="https://projects.arduinocontent.cc/002de214-9985-4db3-875d-cfd24dd458d1.jpg"/><figcaption></figcaption>,<img id="gallery" src="https://projects.arduinocontent.cc/f3dc66cf-c983-4457-a1b0-193018b05113.jpg"/><figcaption></figcaption>,<img id="gallery" src="https://projects.arduinocontent.cc/cb6c2814-0f5e-46fe-8bd3-4d0d87b3e463.jpg"/><figcaption></figcaption>,<img id="gallery" src="https://projects.arduinocontent.cc/9df05665-e9d1-4c75-a3a1-05590bd15a5f.jpg"/><figcaption></figcaption></div> After uploading the code, I placed the circuit inside the 3D enclosure and finished the project </body></html>

LED HOURGLASS USING ARDUINO

A digital hourglass using Arduino, where electronic components will replace sand and glass to simulate the passage of time in a creative and interactive form.