DIY Arduino Oscilloscope

1#define bytesPerPackage 32
2#define switch1 4               //sw1 pin
3#define  switch2 3               //sw2 pin
4
5uint8_t bytesRead;
6byte inputBuffer[bytesPerPackage];
7byte  outputBuffer[bytesPerPackage];
8boolean sw1, sw2;
9
10void setup() {
11  pinMode(switch1,  INPUT);
12  digitalWrite(switch1, HIGH);  // enable internal pullup
13  pinMode(switch2,  INPUT);
14  digitalWrite(switch2, HIGH);
15  ADMUX =  B00000000;           //  set external aref and port
16  ADCSRA = B10101101;           // ADC enable, interrupt  enable, set default prescaler
17  ADCSRB = B00000000;           // free running  mode
18  sei();		        // enable interrupts
19  ADCSRA |=B01000000;           //  start first conversion
20  Serial.begin(115200);
21}
22
23void loop() {
24  sw1 = digitalRead(switch1);
25  sw2 = digitalRead(switch2);
26  if (bytesRead  >= bytesPerPackage) {  // Buffer full. Send the package.
27    cli();
28    bytesRead  = 0;
29    for (uint8_t i = 0; i < bytesPerPackage; i += 2) {
30      byte adch  = inputBuffer[i];
31      if (!sw1) adch |= B00001000;      // switch position  in bits 10 & 11 of each byte pair 
32      if (!sw2) adch |= B00000100;
33      outputBuffer[i]  = adch;
34      outputBuffer[i+1] = inputBuffer[i+1];
35    }
36    sei();
37    Serial.write(outputBuffer, bytesPerPackage);
38  }
39  
40  if (Serial.available())  {                // incoming byte -> set prescaler
41    byte inByte = (byte)Serial.read();
42    cli();
43    ADCSRA= B10101000|(inByte&B00000111);  // last 3 bytes of ADCSRA  set the prescaler
44    sei();
45    ADCSRA |=B01000000;                    //  start first conversion
46  }
47}
48
49ISR(ADC_vect) {
50  if(bytesRead<bytesPerPackage-1){
51    inputBuffer[bytesRead+1] = ADCL;
52    inputBuffer[bytesRead] = ADCH;
53    bytesRead+=2;
54  }
55}
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72

#define bytesPerPackage 32
#define switch1 4               //sw1 pin
#define  switch2 3               //sw2 pin

uint8_t bytesRead;
byte inputBuffer[bytesPerPackage];
byte  outputBuffer[bytesPerPackage];
boolean sw1, sw2;

void setup() {
  pinMode(switch1,  INPUT);
  digitalWrite(switch1, HIGH);  // enable internal pullup
  pinMode(switch2,  INPUT);
  digitalWrite(switch2, HIGH);
  ADMUX =  B00000000;           //  set external aref and port
  ADCSRA = B10101101;           // ADC enable, interrupt  enable, set default prescaler
  ADCSRB = B00000000;           // free running  mode
  sei();		        // enable interrupts
  ADCSRA |=B01000000;           //  start first conversion
  Serial.begin(115200);
}

void loop() {
  sw1 = digitalRead(switch1);
  sw2 = digitalRead(switch2);
  if (bytesRead  >= bytesPerPackage) {  // Buffer full. Send the package.
    cli();
    bytesRead  = 0;
    for (uint8_t i = 0; i < bytesPerPackage; i += 2) {
      byte adch  = inputBuffer[i];
      if (!sw1) adch |= B00001000;      // switch position  in bits 10 & 11 of each byte pair 
      if (!sw2) adch |= B00000100;
      outputBuffer[i]  = adch;
      outputBuffer[i+1] = inputBuffer[i+1];
    }
    sei();
    Serial.write(outputBuffer, bytesPerPackage);
  }
  
  if (Serial.available())  {                // incoming byte -> set prescaler
    byte inByte = (byte)Serial.read();
    cli();
    ADCSRA= B10101000|(inByte&B00000111);  // last 3 bytes of ADCSRA  set the prescaler
    sei();
    ADCSRA |=B01000000;                    //  start first conversion
  }
}

ISR(ADC_vect) {
  if(bytesRead<bytesPerPackage-1){
    inputBuffer[bytesRead+1] = ADCL;
    inputBuffer[bytesRead] = ADCH;
    bytesRead+=2;
  }
}

processing code

csharp

1import processing.serial.*;
2import java.awt.event.KeyEvent;
3
4//  Settings --------------------------------------------------------------------------
5int  serialBaudRate=115200;
6int bufferSize=10000000;      // number of samples (memory  use: 2 bytes per sample)
7float samplesPerLine=1;       // increment 1 screen  line for each [n] samples
8boolean sync=true;            // sync to trig
9float  trigLevelLPF=.0001;     // trigLevel lowpass filter (exponential moving average)
10boolean  hold=false;           // pause
11int prescaler=5;              // ADC prescaler:  3:8 | 4:16 | 5:32 | 6:64 | 7:128
12// -----------------------------------------------------------------------------------
13
14Serial  serial;
15byte[] buffer= new byte[bufferSize*2];
16int writeIndex, prevWriteIndex,  readIndex, trigIndex, trigCounter, loopCounter, windowWidth, windowHeight, offset;
17float  voltageRange, sps, frequency, trigLevel, timer;
18int windowX=30;
19int windowY=50;
20boolean  connected=false;
21String serialPort;
22
23void settings() {
24  size(1000,  600);
25}
26
27void setup() {
28  background(0);
29  surface.setResizable(true);
30  frameRate(50);
31}
32
33void draw() {
34  windowWidth=width-100;
35  windowHeight=height-100;
36  if (!connected) {
37    background(0, 0, 0);
38    text("ARDUINO OSCILLOSCOPE\
39\
40Select  serial port:", 25, 25);
41    for (int i=0; i<Serial.list().length; i++)
42      text("F"+(i+1)+"  - "+Serial.list()[i], 25, 80+i*20);
43  } else {
44    background(0, 0, 0);
45
46    // update frequency counters every second
47    loopCounter++;
48    if (loopCounter>frameRate)  {  
49      loopCounter=0;
50      float elapsedSeconds=(millis()-timer)/1000;
51      timer=millis();
52      sps=(writeIndex-prevWriteIndex)/elapsedSeconds;  //  sample rate
53      if (sps<0)sps+=bufferSize;
54      prevWriteIndex=writeIndex;
55      frequency=trigCounter/elapsedSeconds;            // signal frequency
56      trigCounter=0;
57    }
58
59    // read switch position & set voltage range
60    boolean switch1=((buffer[writeIndex*2]&(byte)8)==8);                                                 
61    boolean switch2=((buffer[writeIndex*2]&(byte)4)==4);
62    if (!switch1&&!switch2) voltageRange=20;
63    if (!switch1&&switch2) voltageRange=10;
64    if (switch1&&!switch2) voltageRange=6.64;
65    if (switch1&&switch2) voltageRange=5;
66
67    // print voltage scale
68    for (int n=0; n<=10; n++)                                                                           
69      text(nf(voltageRange/10*n, 2, 2)+"V", windowX+windowWidth+5, windowY+windowHeight-(n*windowHeight/10));
70
71    // print interface and statistics
72    text("[F1-F2] ZOOM | [F3] SYNC: "+sync+"  | [F4] HOLD: "+hold+" | [F5-F6] TRIG LPF | [F7-F8] PRESCALER: "+nf((pow(2, prescaler)),  1, 0)+" | [<--->] OFFSET", 25, 25);
73    text("frequency: "+nf(frequency,  5, 2)+"Hz"
74      +" | average DCV: "+nf(trigLevel/1024*voltageRange, 2, 2)+"V"
75      +" | samplerate: "+nf(sps, 5, 2)+"Hz"
76      +" | samples per line:  "+samplesPerLine
77      +" | division: "+samplesPerLine/sps*(float)width*100+"ms",  25, height-20);
78
79    // draw trigLevel (= average voltage) line
80    stroke(0,  0, 100);                                                                                   
81    int trigLevelHeight=(int)(trigLevel*(float)windowHeight/1024);
82    line(windowX,  windowY+windowHeight-trigLevelHeight, windowX+windowWidth, windowY+windowHeight-trigLevelHeight);  
83
84    // draw grid
85    stroke(50);                                                                                           
86    for (float n=0; n<=windowWidth; n+=(float)windowWidth/10) 
87      line(n+windowX,  windowY, n+windowX, windowHeight+windowY); 
88    for (float n=0; n<=windowHeight;  n+=(float)windowHeight/10) 
89      line(windowX, n+windowY, windowX+windowWidth,  n+windowY);
90
91    // ------------------------------
92    // DRAW WAVEFORM
93    // ------------------------------
94    stroke(255);
95    float prevSampleValue=0;
96    if (sync) readIndex=trigIndex;                               // sync: start  reading from last trig position
97    if (!sync) readIndex=writeIndex;                             //  no sync: start reading from last sample we received
98    readIndex+=offset;
99    float lineIncr=(float)1/samplesPerLine;
100    if (lineIncr<1) lineIncr=1;
101    for (float line=0; line<windowWidth; line+=lineIncr) {                                          //  cycle screen lines (from right to left)
102      float sampleValue=(float)getValueFromBuffer((int)((float)readIndex-line*samplesPerLine));     // get the value for the screen line
103      sampleValue*=(float)windowHeight/1024;                                                        // scale to windowHeight
104      if (line>0)
105        line(windowX+windowWidth-line, 
106          windowY+windowHeight-prevSampleValue,  
107          windowX+windowWidth-line-lineIncr, 
108          windowY+windowHeight-sampleValue);
109      prevSampleValue=sampleValue;
110    }
111
112    // ------------------------------
113    // BUFFER INCOMING BYTES & TRIG 
114    // ------------------------------
115    if (hold) {
116      serial.clear();                                                                                      //  HOLD: don't receive samples; clear serial buffer
117    } else {
118      while  (serial.available ()>0) {                                                                      //  RUN: receive samples
119        writeIndex++;  
120        if (writeIndex>=bufferSize)  writeIndex=0;                                                          // handle  overflow
121        buffer[writeIndex+writeIndex]=(byte)serial.read();                                                 //  add 1 sample (2 bytes) to buffer 
122        buffer[writeIndex+writeIndex+1]=(byte)serial.read();
123        trigLevel=trigLevel*(1-trigLevelLPF)+(float)getValueFromBuffer(writeIndex)*trigLevelLPF;           // level for trigger intersection = exponential moving average of voltage
124        if (getValueFromBuffer(writeIndex)>=trigLevel&& getValueFromBuffer(writeIndex-1)<trigLevel)  {      // rising intersect detected
125          trigIndex=writeIndex;                                                                            //  set trigIndex (index of buffer that corresponds to last trig)
126          trigCounter++;                                                                                   //  count trigs (to calculate the frequency)
127        }
128      }
129    }
130  }
131}
132
133
134//  Read value from buffer
135int getValueFromBuffer(int index) {                                                                      
136  while (index<0) index+=bufferSize;                                                                       //  handle overflow of circular buffer
137  return((buffer[index*2]&3)<<8 | buffer[index*2+1]&0xff);                                                 // convert bytes to int
138}
139
140//  Handle keys
141void keyPressed() {  
142  if (key == CODED) {
143    if (connected)  {
144      if (keyCode == KeyEvent.VK_F1) {
145        samplesPerLine*=1.1;
146        if (samplesPerLine*windowWidth>bufferSize) samplesPerLine=bufferSize/windowWidth;
147      }
148      if (keyCode == KeyEvent.VK_F2) {
149        samplesPerLine/=1.1;
150        if (samplesPerLine<1/(float)windowWidth) samplesPerLine=1/(float)windowWidth;
151      }
152      if (keyCode == KeyEvent.VK_F3) {
153        sync=!sync;
154      }
155      if (keyCode == KeyEvent.VK_F4) {
156        hold=!hold;
157      }
158      if  (keyCode == KeyEvent.VK_F5) {
159        if (trigLevelLPF<.01) trigLevelLPF*=10;
160      }
161      if (keyCode == KeyEvent.VK_F6) {
162        if (trigLevelLPF>.000001)  trigLevelLPF/=10;
163      }
164      if (keyCode == KeyEvent.VK_F7) {
165        if  (prescaler>3) prescaler--;
166        serial.write((byte)prescaler);
167      }
168      if (keyCode == KeyEvent.VK_F8) {
169        if (prescaler<7) prescaler++;
170        serial.write((byte)prescaler);
171      }
172      if (keyCode == LEFT)  {
173        offset-=samplesPerLine*20;
174        if (offset<-bufferSize) offset=-bufferSize;
175      }
176      if (keyCode == RIGHT) {
177        offset+=samplesPerLine*20;
178        if (offset>0) offset=0;
179      }
180    } else {
181      serial = new  Serial(this, Serial.list()[keyCode-112], serialBaudRate);
182      serial.write((byte)prescaler);
183      connected=true;
184    }
185  }
186}

import processing.serial.*;
import java.awt.event.KeyEvent;

//  Settings --------------------------------------------------------------------------
int  serialBaudRate=115200;
int bufferSize=10000000;      // number of samples (memory  use: 2 bytes per sample)
float samplesPerLine=1;       // increment 1 screen  line for each [n] samples
boolean sync=true;            // sync to trig
float  trigLevelLPF=.0001;     // trigLevel lowpass filter (exponential moving average)
boolean  hold=false;           // pause
int prescaler=5;              // ADC prescaler:  3:8 | 4:16 | 5:32 | 6:64 | 7:128
// -----------------------------------------------------------------------------------

Serial  serial;
byte[] buffer= new byte[bufferSize*2];
int writeIndex, prevWriteIndex,  readIndex, trigIndex, trigCounter, loopCounter, windowWidth, windowHeight, offset;
float  voltageRange, sps, frequency, trigLevel, timer;
int windowX=30;
int windowY=50;
boolean  connected=false;
String serialPort;

void settings() {
  size(1000,  600);
}

void setup() {
  background(0);
  surface.setResizable(true);
  frameRate(50);
}

void draw() {
  windowWidth=width-100;
  windowHeight=height-100;
  if (!connected) {
    background(0, 0, 0);
    text("ARDUINO OSCILLOSCOPE\
\
Select  serial port:", 25, 25);
    for (int i=0; i<Serial.list().length; i++)
      text("F"+(i+1)+"  - "+Serial.list()[i], 25, 80+i*20);
  } else {
    background(0, 0, 0);

    // update frequency counters every second
    loopCounter++;
    if (loopCounter>frameRate)  {  
      loopCounter=0;
      float elapsedSeconds=(millis()-timer)/1000;
      timer=millis();
      sps=(writeIndex-prevWriteIndex)/elapsedSeconds;  //  sample rate
      if (sps<0)sps+=bufferSize;
      prevWriteIndex=writeIndex;
      frequency=trigCounter/elapsedSeconds;            // signal frequency
      trigCounter=0;
    }

    // read switch position & set voltage range
    boolean switch1=((buffer[writeIndex*2]&(byte)8)==8);                                                 
    boolean switch2=((buffer[writeIndex*2]&(byte)4)==4);
    if (!switch1&&!switch2) voltageRange=20;
    if (!switch1&&switch2) voltageRange=10;
    if (switch1&&!switch2) voltageRange=6.64;
    if (switch1&&switch2) voltageRange=5;

    // print voltage scale
    for (int n=0; n<=10; n++)                                                                           
      text(nf(voltageRange/10*n, 2, 2)+"V", windowX+windowWidth+5, windowY+windowHeight-(n*windowHeight/10));

    // print interface and statistics
    text("[F1-F2] ZOOM | [F3] SYNC: "+sync+"  | [F4] HOLD: "+hold+" | [F5-F6] TRIG LPF | [F7-F8] PRESCALER: "+nf((pow(2, prescaler)),  1, 0)+" | [<--->] OFFSET", 25, 25);
    text("frequency: "+nf(frequency,  5, 2)+"Hz"
      +" | average DCV: "+nf(trigLevel/1024*voltageRange, 2, 2)+"V"
      +" | samplerate: "+nf(sps, 5, 2)+"Hz"
      +" | samples per line:  "+samplesPerLine
      +" | division: "+samplesPerLine/sps*(float)width*100+"ms",  25, height-20);

    // draw trigLevel (= average voltage) line
    stroke(0,  0, 100);                                                                                   
    int trigLevelHeight=(int)(trigLevel*(float)windowHeight/1024);
    line(windowX,  windowY+windowHeight-trigLevelHeight, windowX+windowWidth, windowY+windowHeight-trigLevelHeight);  

    // draw grid
    stroke(50);                                                                                           
    for (float n=0; n<=windowWidth; n+=(float)windowWidth/10) 
      line(n+windowX,  windowY, n+windowX, windowHeight+windowY); 
    for (float n=0; n<=windowHeight;  n+=(float)windowHeight/10) 
      line(windowX, n+windowY, windowX+windowWidth,  n+windowY);

    // ------------------------------
    // DRAW WAVEFORM
    // ------------------------------
    stroke(255);
    float prevSampleValue=0;
    if (sync) readIndex=trigIndex;                               // sync: start  reading from last trig position
    if (!sync) readIndex=writeIndex;                             //  no sync: start reading from last sample we received
    readIndex+=offset;
    float lineIncr=(float)1/samplesPerLine;
    if (lineIncr<1) lineIncr=1;
    for (float line=0; line<windowWidth; line+=lineIncr) {                                          //  cycle screen lines (from right to left)
      float sampleValue=(float)getValueFromBuffer((int)((float)readIndex-line*samplesPerLine));     // get the value for the screen line
      sampleValue*=(float)windowHeight/1024;                                                        // scale to windowHeight
      if (line>0)
        line(windowX+windowWidth-line, 
          windowY+windowHeight-prevSampleValue,  
          windowX+windowWidth-line-lineIncr, 
          windowY+windowHeight-sampleValue);
      prevSampleValue=sampleValue;
    }

    // ------------------------------
    // BUFFER INCOMING BYTES & TRIG 
    // ------------------------------
    if (hold) {
      serial.clear();                                                                                      //  HOLD: don't receive samples; clear serial buffer
    } else {
      while  (serial.available ()>0) {                                                                      //  RUN: receive samples
        writeIndex++;  
        if (writeIndex>=bufferSize)  writeIndex=0;                                                          // handle  overflow
        buffer[writeIndex+writeIndex]=(byte)serial.read();                                                 //  add 1 sample (2 bytes) to buffer 
        buffer[writeIndex+writeIndex+1]=(byte)serial.read();
        trigLevel=trigLevel*(1-trigLevelLPF)+(float)getValueFromBuffer(writeIndex)*trigLevelLPF;           // level for trigger intersection = exponential moving average of voltage
        if (getValueFromBuffer(writeIndex)>=trigLevel&& getValueFromBuffer(writeIndex-1)<trigLevel)  {      // rising intersect detected
          trigIndex=writeIndex;                                                                            //  set trigIndex (index of buffer that corresponds to last trig)
          trigCounter++;                                                                                   //  count trigs (to calculate the frequency)
        }
      }
    }
  }
}


//  Read value from buffer
int getValueFromBuffer(int index) {                                                                      
  while (index<0) index+=bufferSize;                                                                       //  handle overflow of circular buffer
  return((buffer[index*2]&3)<<8 | buffer[index*2+1]&0xff);                                                 // convert bytes to int
}

//  Handle keys
void keyPressed() {  
  if (key == CODED) {
    if (connected)  {
      if (keyCode == KeyEvent.VK_F1) {
        samplesPerLine*=1.1;
        if (samplesPerLine*windowWidth>bufferSize) samplesPerLine=bufferSize/windowWidth;
      }
      if (keyCode == KeyEvent.VK_F2) {
        samplesPerLine/=1.1;
        if (samplesPerLine<1/(float)windowWidth) samplesPerLine=1/(float)windowWidth;
      }
      if (keyCode == KeyEvent.VK_F3) {
        sync=!sync;
      }
      if (keyCode == KeyEvent.VK_F4) {
        hold=!hold;
      }
      if  (keyCode == KeyEvent.VK_F5) {
        if (trigLevelLPF<.01) trigLevelLPF*=10;
      }
      if (keyCode == KeyEvent.VK_F6) {
        if (trigLevelLPF>.000001)  trigLevelLPF/=10;
      }
      if (keyCode == KeyEvent.VK_F7) {
        if  (prescaler>3) prescaler--;
        serial.write((byte)prescaler);
      }
      if (keyCode == KeyEvent.VK_F8) {
        if (prescaler<7) prescaler++;
        serial.write((byte)prescaler);
      }
      if (keyCode == LEFT)  {
        offset-=samplesPerLine*20;
        if (offset<-bufferSize) offset=-bufferSize;
      }
      if (keyCode == RIGHT) {
        offset+=samplesPerLine*20;
        if (offset>0) offset=0;
      }
    } else {
      serial = new  Serial(this, Serial.list()[keyCode-112], serialBaudRate);
      serial.write((byte)prescaler);
      connected=true;
    }
  }
}

code

csharp

1#define bytesPerPackage 32
2#define switch1 4               //sw1 pin
3#define   switch2 3               //sw2 pin
4
5uint8_t bytesRead;
6byte inputBuffer[bytesPerPackage];
7byte   outputBuffer[bytesPerPackage];
8boolean sw1, sw2;
9
10void setup() {
11  pinMode(switch1,   INPUT);
12  digitalWrite(switch1, HIGH);  // enable internal pullup
13  pinMode(switch2,   INPUT);
14  digitalWrite(switch2, HIGH);
15  ADMUX =  B00000000;           //   set external aref and port
16  ADCSRA = B10101101;           // ADC enable, interrupt   enable, set default prescaler
17  ADCSRB = B00000000;           // free running   mode
18  sei();		        // enable interrupts
19  ADCSRA |=B01000000;           //   start first conversion
20  Serial.begin(115200);
21}
22
23void loop() {
24   sw1 = digitalRead(switch1);
25  sw2 = digitalRead(switch2);
26  if (bytesRead   >= bytesPerPackage) {  // Buffer full. Send the package.
27    cli();
28    bytesRead   = 0;
29    for (uint8_t i = 0; i < bytesPerPackage; i += 2) {
30      byte adch   = inputBuffer[i];
31      if (!sw1) adch |= B00001000;      // switch position   in bits 10 & 11 of each byte pair 
32      if (!sw2) adch |= B00000100;
33      outputBuffer[i]   = adch;
34      outputBuffer[i+1] = inputBuffer[i+1];
35    }
36    sei();
37     Serial.write(outputBuffer, bytesPerPackage);
38  }
39  
40  if (Serial.available())   {                // incoming byte -> set prescaler
41    byte inByte = (byte)Serial.read();
42     cli();
43    ADCSRA= B10101000|(inByte&B00000111);  // last 3 bytes of ADCSRA   set the prescaler
44    sei();
45    ADCSRA |=B01000000;                    //   start first conversion
46  }
47}
48
49ISR(ADC_vect) {
50  if(bytesRead<bytesPerPackage-1){
51     inputBuffer[bytesRead+1] = ADCL;
52    inputBuffer[bytesRead] = ADCH;
53    bytesRead+=2;
54   }
55}
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72

#define bytesPerPackage 32
#define switch1 4               //sw1 pin
#define   switch2 3               //sw2 pin

uint8_t bytesRead;
byte inputBuffer[bytesPerPackage];
byte   outputBuffer[bytesPerPackage];
boolean sw1, sw2;

void setup() {
  pinMode(switch1,   INPUT);
  digitalWrite(switch1, HIGH);  // enable internal pullup
  pinMode(switch2,   INPUT);
  digitalWrite(switch2, HIGH);
  ADMUX =  B00000000;           //   set external aref and port
  ADCSRA = B10101101;           // ADC enable, interrupt   enable, set default prescaler
  ADCSRB = B00000000;           // free running   mode
  sei();		        // enable interrupts
  ADCSRA |=B01000000;           //   start first conversion
  Serial.begin(115200);
}

void loop() {
   sw1 = digitalRead(switch1);
  sw2 = digitalRead(switch2);
  if (bytesRead   >= bytesPerPackage) {  // Buffer full. Send the package.
    cli();
    bytesRead   = 0;
    for (uint8_t i = 0; i < bytesPerPackage; i += 2) {
      byte adch   = inputBuffer[i];
      if (!sw1) adch |= B00001000;      // switch position   in bits 10 & 11 of each byte pair 
      if (!sw2) adch |= B00000100;
      outputBuffer[i]   = adch;
      outputBuffer[i+1] = inputBuffer[i+1];
    }
    sei();
     Serial.write(outputBuffer, bytesPerPackage);
  }
  
  if (Serial.available())   {                // incoming byte -> set prescaler
    byte inByte = (byte)Serial.read();
     cli();
    ADCSRA= B10101000|(inByte&B00000111);  // last 3 bytes of ADCSRA   set the prescaler
    sei();
    ADCSRA |=B01000000;                    //   start first conversion
  }
}

ISR(ADC_vect) {
  if(bytesRead<bytesPerPackage-1){
     inputBuffer[bytesRead+1] = ADCL;
    inputBuffer[bytesRead] = ADCH;
    bytesRead+=2;
   }
}

processing code

csharp

1import processing.serial.*;
2import java.awt.event.KeyEvent;
3
4//   Settings --------------------------------------------------------------------------
5int   serialBaudRate=115200;
6int bufferSize=10000000;      // number of samples (memory   use: 2 bytes per sample)
7float samplesPerLine=1;       // increment 1 screen   line for each [n] samples
8boolean sync=true;            // sync to trig
9float   trigLevelLPF=.0001;     // trigLevel lowpass filter (exponential moving average)
10boolean   hold=false;           // pause
11int prescaler=5;              // ADC prescaler:   3:8 | 4:16 | 5:32 | 6:64 | 7:128
12// -----------------------------------------------------------------------------------
13
14Serial   serial;
15byte[] buffer= new byte[bufferSize*2];
16int writeIndex, prevWriteIndex,   readIndex, trigIndex, trigCounter, loopCounter, windowWidth, windowHeight, offset;
17float   voltageRange, sps, frequency, trigLevel, timer;
18int windowX=30;
19int windowY=50;
20boolean   connected=false;
21String serialPort;
22
23void settings() {
24  size(1000,   600);
25}
26
27void setup() {
28  background(0);
29  surface.setResizable(true);
30   frameRate(50);
31}
32
33void draw() {
34  windowWidth=width-100;
35  windowHeight=height-100;
36   if (!connected) {
37    background(0, 0, 0);
38    text("ARDUINO OSCILLOSCOPE\
39\
40Select   serial port:", 25, 25);
41    for (int i=0; i<Serial.list().length; i++)
42      text("F"+(i+1)+"   - "+Serial.list()[i], 25, 80+i*20);
43  } else {
44    background(0, 0, 0);
45
46     // update frequency counters every second
47    loopCounter++;
48    if (loopCounter>frameRate)   {  
49      loopCounter=0;
50      float elapsedSeconds=(millis()-timer)/1000;
51       timer=millis();
52      sps=(writeIndex-prevWriteIndex)/elapsedSeconds;  //   sample rate
53      if (sps<0)sps+=bufferSize;
54      prevWriteIndex=writeIndex;
55       frequency=trigCounter/elapsedSeconds;            // signal frequency
56      trigCounter=0;
57     }
58
59    // read switch position & set voltage range
60    boolean switch1=((buffer[writeIndex*2]&(byte)8)==8);                                                  
61    boolean switch2=((buffer[writeIndex*2]&(byte)4)==4);
62     if (!switch1&&!switch2) voltageRange=20;
63    if (!switch1&&switch2) voltageRange=10;
64     if (switch1&&!switch2) voltageRange=6.64;
65    if (switch1&&switch2) voltageRange=5;
66
67     // print voltage scale
68    for (int n=0; n<=10; n++)                                                                           
69       text(nf(voltageRange/10*n, 2, 2)+"V", windowX+windowWidth+5, windowY+windowHeight-(n*windowHeight/10));
70
71     // print interface and statistics
72    text("[F1-F2] ZOOM | [F3] SYNC: "+sync+"   | [F4] HOLD: "+hold+" | [F5-F6] TRIG LPF | [F7-F8] PRESCALER: "+nf((pow(2, prescaler)),   1, 0)+" | [<--->] OFFSET", 25, 25);
73    text("frequency: "+nf(frequency,   5, 2)+"Hz"
74      +" | average DCV: "+nf(trigLevel/1024*voltageRange, 2, 2)+"V"
75       +" | samplerate: "+nf(sps, 5, 2)+"Hz"
76      +" | samples per line:   "+samplesPerLine
77      +" | division: "+samplesPerLine/sps*(float)width*100+"ms",   25, height-20);
78
79    // draw trigLevel (= average voltage) line
80    stroke(0,   0, 100);                                                                                   
81     int trigLevelHeight=(int)(trigLevel*(float)windowHeight/1024);
82    line(windowX,   windowY+windowHeight-trigLevelHeight, windowX+windowWidth, windowY+windowHeight-trigLevelHeight);   
83
84    // draw grid
85    stroke(50);                                                                                           
86     for (float n=0; n<=windowWidth; n+=(float)windowWidth/10) 
87      line(n+windowX,   windowY, n+windowX, windowHeight+windowY); 
88    for (float n=0; n<=windowHeight;   n+=(float)windowHeight/10) 
89      line(windowX, n+windowY, windowX+windowWidth,   n+windowY);
90
91    // ------------------------------
92    // DRAW WAVEFORM
93     // ------------------------------
94    stroke(255);
95    float prevSampleValue=0;
96     if (sync) readIndex=trigIndex;                               // sync: start   reading from last trig position
97    if (!sync) readIndex=writeIndex;                             //   no sync: start reading from last sample we received
98    readIndex+=offset;
99     float lineIncr=(float)1/samplesPerLine;
100    if (lineIncr<1) lineIncr=1;
101     for (float line=0; line<windowWidth; line+=lineIncr) {                                          //   cycle screen lines (from right to left)
102      float sampleValue=(float)getValueFromBuffer((int)((float)readIndex-line*samplesPerLine));      // get the value for the screen line
103      sampleValue*=(float)windowHeight/1024;                                                         // scale to windowHeight
104       if (line>0)
105        line(windowX+windowWidth-line, 
106          windowY+windowHeight-prevSampleValue,   
107          windowX+windowWidth-line-lineIncr, 
108          windowY+windowHeight-sampleValue);
109       prevSampleValue=sampleValue;
110    }
111
112    // ------------------------------
113     // BUFFER INCOMING BYTES & TRIG 
114    // ------------------------------
115     if (hold) {
116      serial.clear();                                                                                      //   HOLD: don't receive samples; clear serial buffer
117    } else {
118      while   (serial.available ()>0) {                                                                      //   RUN: receive samples
119        writeIndex++;  
120        if (writeIndex>=bufferSize)   writeIndex=0;                                                          // handle   overflow
121        buffer[writeIndex+writeIndex]=(byte)serial.read();                                                 //   add 1 sample (2 bytes) to buffer 
122        buffer[writeIndex+writeIndex+1]=(byte)serial.read();
123         trigLevel=trigLevel*(1-trigLevelLPF)+(float)getValueFromBuffer(writeIndex)*trigLevelLPF;            // level for trigger intersection = exponential moving average of voltage
124         if (getValueFromBuffer(writeIndex)>=trigLevel&& getValueFromBuffer(writeIndex-1)<trigLevel)   {      // rising intersect detected
125          trigIndex=writeIndex;                                                                            //   set trigIndex (index of buffer that corresponds to last trig)
126          trigCounter++;                                                                                    //   count trigs (to calculate the frequency)
127        }
128      }
129    }
130  }
131}
132
133
134//   Read value from buffer
135int getValueFromBuffer(int index) {                                                                      
136   while (index<0) index+=bufferSize;                                                                       //   handle overflow of circular buffer
137  return((buffer[index*2]&3)<<8 | buffer[index*2+1]&0xff);                                                  // convert bytes to int
138}
139
140//   Handle keys
141void keyPressed() {  
142  if (key == CODED) {
143    if (connected)   {
144      if (keyCode == KeyEvent.VK_F1) {
145        samplesPerLine*=1.1;
146         if (samplesPerLine*windowWidth>bufferSize) samplesPerLine=bufferSize/windowWidth;
147       }
148      if (keyCode == KeyEvent.VK_F2) {
149        samplesPerLine/=1.1;
150         if (samplesPerLine<1/(float)windowWidth) samplesPerLine=1/(float)windowWidth;
151       }
152      if (keyCode == KeyEvent.VK_F3) {
153        sync=!sync;
154      }
155       if (keyCode == KeyEvent.VK_F4) {
156        hold=!hold;
157      }
158      if   (keyCode == KeyEvent.VK_F5) {
159        if (trigLevelLPF<.01) trigLevelLPF*=10;
160       }
161      if (keyCode == KeyEvent.VK_F6) {
162        if (trigLevelLPF>.000001)   trigLevelLPF/=10;
163      }
164      if (keyCode == KeyEvent.VK_F7) {
165        if   (prescaler>3) prescaler--;
166        serial.write((byte)prescaler);
167      }
168       if (keyCode == KeyEvent.VK_F8) {
169        if (prescaler<7) prescaler++;
170         serial.write((byte)prescaler);
171      }
172      if (keyCode == LEFT)   {
173        offset-=samplesPerLine*20;
174        if (offset<-bufferSize) offset=-bufferSize;
175       }
176      if (keyCode == RIGHT) {
177        offset+=samplesPerLine*20;
178         if (offset>0) offset=0;
179      }
180    } else {
181      serial = new   Serial(this, Serial.list()[keyCode-112], serialBaudRate);
182      serial.write((byte)prescaler);
183       connected=true;
184    }
185  }
186}

import processing.serial.*;
import java.awt.event.KeyEvent;

//   Settings --------------------------------------------------------------------------
int   serialBaudRate=115200;
int bufferSize=10000000;      // number of samples (memory   use: 2 bytes per sample)
float samplesPerLine=1;       // increment 1 screen   line for each [n] samples
boolean sync=true;            // sync to trig
float   trigLevelLPF=.0001;     // trigLevel lowpass filter (exponential moving average)
boolean   hold=false;           // pause
int prescaler=5;              // ADC prescaler:   3:8 | 4:16 | 5:32 | 6:64 | 7:128
// -----------------------------------------------------------------------------------

Serial   serial;
byte[] buffer= new byte[bufferSize*2];
int writeIndex, prevWriteIndex,   readIndex, trigIndex, trigCounter, loopCounter, windowWidth, windowHeight, offset;
float   voltageRange, sps, frequency, trigLevel, timer;
int windowX=30;
int windowY=50;
boolean   connected=false;
String serialPort;

void settings() {
  size(1000,   600);
}

void setup() {
  background(0);
  surface.setResizable(true);
   frameRate(50);
}

void draw() {
  windowWidth=width-100;
  windowHeight=height-100;
   if (!connected) {
    background(0, 0, 0);
    text("ARDUINO OSCILLOSCOPE\
\
Select   serial port:", 25, 25);
    for (int i=0; i<Serial.list().length; i++)
      text("F"+(i+1)+"   - "+Serial.list()[i], 25, 80+i*20);
  } else {
    background(0, 0, 0);

     // update frequency counters every second
    loopCounter++;
    if (loopCounter>frameRate)   {  
      loopCounter=0;
      float elapsedSeconds=(millis()-timer)/1000;
       timer=millis();
      sps=(writeIndex-prevWriteIndex)/elapsedSeconds;  //   sample rate
      if (sps<0)sps+=bufferSize;
      prevWriteIndex=writeIndex;
       frequency=trigCounter/elapsedSeconds;            // signal frequency
      trigCounter=0;
     }

    // read switch position & set voltage range
    boolean switch1=((buffer[writeIndex*2]&(byte)8)==8);                                                  
    boolean switch2=((buffer[writeIndex*2]&(byte)4)==4);
     if (!switch1&&!switch2) voltageRange=20;
    if (!switch1&&switch2) voltageRange=10;
     if (switch1&&!switch2) voltageRange=6.64;
    if (switch1&&switch2) voltageRange=5;

     // print voltage scale
    for (int n=0; n<=10; n++)                                                                           
       text(nf(voltageRange/10*n, 2, 2)+"V", windowX+windowWidth+5, windowY+windowHeight-(n*windowHeight/10));

     // print interface and statistics
    text("[F1-F2] ZOOM | [F3] SYNC: "+sync+"   | [F4] HOLD: "+hold+" | [F5-F6] TRIG LPF | [F7-F8] PRESCALER: "+nf((pow(2, prescaler)),   1, 0)+" | [<--->] OFFSET", 25, 25);
    text("frequency: "+nf(frequency,   5, 2)+"Hz"
      +" | average DCV: "+nf(trigLevel/1024*voltageRange, 2, 2)+"V"
       +" | samplerate: "+nf(sps, 5, 2)+"Hz"
      +" | samples per line:   "+samplesPerLine
      +" | division: "+samplesPerLine/sps*(float)width*100+"ms",   25, height-20);

    // draw trigLevel (= average voltage) line
    stroke(0,   0, 100);                                                                                   
     int trigLevelHeight=(int)(trigLevel*(float)windowHeight/1024);
    line(windowX,   windowY+windowHeight-trigLevelHeight, windowX+windowWidth, windowY+windowHeight-trigLevelHeight);   

    // draw grid
    stroke(50);                                                                                           
     for (float n=0; n<=windowWidth; n+=(float)windowWidth/10) 
      line(n+windowX,   windowY, n+windowX, windowHeight+windowY); 
    for (float n=0; n<=windowHeight;   n+=(float)windowHeight/10) 
      line(windowX, n+windowY, windowX+windowWidth,   n+windowY);

    // ------------------------------
    // DRAW WAVEFORM
     // ------------------------------
    stroke(255);
    float prevSampleValue=0;
     if (sync) readIndex=trigIndex;                               // sync: start   reading from last trig position
    if (!sync) readIndex=writeIndex;                             //   no sync: start reading from last sample we received
    readIndex+=offset;
     float lineIncr=(float)1/samplesPerLine;
    if (lineIncr<1) lineIncr=1;
     for (float line=0; line<windowWidth; line+=lineIncr) {                                          //   cycle screen lines (from right to left)
      float sampleValue=(float)getValueFromBuffer((int)((float)readIndex-line*samplesPerLine));      // get the value for the screen line
      sampleValue*=(float)windowHeight/1024;                                                         // scale to windowHeight
       if (line>0)
        line(windowX+windowWidth-line, 
          windowY+windowHeight-prevSampleValue,   
          windowX+windowWidth-line-lineIncr, 
          windowY+windowHeight-sampleValue);
       prevSampleValue=sampleValue;
    }

    // ------------------------------
     // BUFFER INCOMING BYTES & TRIG 
    // ------------------------------
     if (hold) {
      serial.clear();                                                                                      //   HOLD: don't receive samples; clear serial buffer
    } else {
      while   (serial.available ()>0) {                                                                      //   RUN: receive samples
        writeIndex++;  
        if (writeIndex>=bufferSize)   writeIndex=0;                                                          // handle   overflow
        buffer[writeIndex+writeIndex]=(byte)serial.read();                                                 //   add 1 sample (2 bytes) to buffer 
        buffer[writeIndex+writeIndex+1]=(byte)serial.read();
         trigLevel=trigLevel*(1-trigLevelLPF)+(float)getValueFromBuffer(writeIndex)*trigLevelLPF;            // level for trigger intersection = exponential moving average of voltage
         if (getValueFromBuffer(writeIndex)>=trigLevel&& getValueFromBuffer(writeIndex-1)<trigLevel)   {      // rising intersect detected
          trigIndex=writeIndex;                                                                            //   set trigIndex (index of buffer that corresponds to last trig)
          trigCounter++;                                                                                    //   count trigs (to calculate the frequency)
        }
      }
    }
  }
}


//   Read value from buffer
int getValueFromBuffer(int index) {                                                                      
   while (index<0) index+=bufferSize;                                                                       //   handle overflow of circular buffer
  return((buffer[index*2]&3)<<8 | buffer[index*2+1]&0xff);                                                  // convert bytes to int
}

//   Handle keys
void keyPressed() {  
  if (key == CODED) {
    if (connected)   {
      if (keyCode == KeyEvent.VK_F1) {
        samplesPerLine*=1.1;
         if (samplesPerLine*windowWidth>bufferSize) samplesPerLine=bufferSize/windowWidth;
       }
      if (keyCode == KeyEvent.VK_F2) {
        samplesPerLine/=1.1;
         if (samplesPerLine<1/(float)windowWidth) samplesPerLine=1/(float)windowWidth;
       }
      if (keyCode == KeyEvent.VK_F3) {
        sync=!sync;
      }
       if (keyCode == KeyEvent.VK_F4) {
        hold=!hold;
      }
      if   (keyCode == KeyEvent.VK_F5) {
        if (trigLevelLPF<.01) trigLevelLPF*=10;
       }
      if (keyCode == KeyEvent.VK_F6) {
        if (trigLevelLPF>.000001)   trigLevelLPF/=10;
      }
      if (keyCode == KeyEvent.VK_F7) {
        if   (prescaler>3) prescaler--;
        serial.write((byte)prescaler);
      }
       if (keyCode == KeyEvent.VK_F8) {
        if (prescaler<7) prescaler++;
         serial.write((byte)prescaler);
      }
      if (keyCode == LEFT)   {
        offset-=samplesPerLine*20;
        if (offset<-bufferSize) offset=-bufferSize;
       }
      if (keyCode == RIGHT) {
        offset+=samplesPerLine*20;
         if (offset>0) offset=0;
      }
    } else {
      serial = new   Serial(this, Serial.list()[keyCode-112], serialBaudRate);
      serial.write((byte)prescaler);
       connected=true;
    }
  }
}

processing code 2

csharp

1import processing.serial.*;
2import java.awt.event.KeyEvent;
3
4//  Settings --------------------------------------------------------------------------
5int  serialBaudRate=115200;
6int bufferSize=10000000;      // number of samples (memory  use: 2 bytes per sample)
7float samplesPerLine=1;       // increment 1 screen  line for each [n] samples
8boolean sync=true;            // sync to trig
9float  trigLevelLPF=.0001;     // trigLevel lowpass filter (exponential moving average)
10boolean  hold=false;           // pause
11int prescaler=5;              // ADC prescaler:  3:8 | 4:16 | 5:32 | 6:64 | 7:128
12// -----------------------------------------------------------------------------------
13
14Serial  serial;
15PFont font= createFont("Lucida Console", 12, false);
16byte[] buffer=  new byte[bufferSize*2];
17int writeIndex, prevWriteIndex, readIndex, trigIndex,  trigCounter, loopCounter, windowWidth, windowHeight, offset;
18float voltageRange,  sps, frequency, trigLevel, timer;
19int windowX=30;
20int windowY=50;
21boolean  connected=false;
22String serialPort;
23
24void setup() {
25  size(1000, 600);
26  background(0, 0, 0);
27  frame.setResizable(true);
28  frameRate(50);    
29  textFont(font);
30  text("ARDUINO OSCILLOSCOPE\
31\
32Select serial port:", 25,  25);
33  for (int i=0;i<Serial.list().length;i++)
34    text("F"+(i+1)+" -  "+Serial.list()[i], 25, 80+i*20);
35}
36
37void draw() {
38  windowWidth=width-100;
39  windowHeight=height-100;
40
41  if (connected) {
42    background(0, 0, 0);
43    
44    // update frequency counters every second
45    loopCounter++;
46    if (loopCounter>frameRate) {  
47      loopCounter=0;
48      float elapsedSeconds=(millis()-timer)/1000;
49      timer=millis();
50      sps=(writeIndex-prevWriteIndex)/elapsedSeconds;  //  sample rate
51      if (sps<0)sps+=bufferSize;
52      prevWriteIndex=writeIndex;
53      frequency=trigCounter/elapsedSeconds;            // signal frequency
54      trigCounter=0;
55    }
56
57    // read switch position & set voltage range
58    boolean switch1=((buffer[writeIndex*2]&(byte)8)==8);                                                 
59    boolean switch2=((buffer[writeIndex*2]&(byte)4)==4);
60    if (!switch1&&!switch2) voltageRange=20;
61    if (!switch1&&switch2) voltageRange=10;
62    if (switch1&&!switch2) voltageRange=6.64;
63    if (switch1&&switch2) voltageRange=5;
64
65    // print voltage scale
66    for (int n=0; n<=10; n++)                                                                           
67      text(nf(voltageRange/10*n, 2, 2)+"V", windowX+windowWidth+5, windowY+windowHeight-(n*windowHeight/10));
68
69    // print interface and statistics
70    text("[F1-F2] ZOOM | [F3] SYNC: "+sync+"  | [F4] HOLD: "+hold+" | [F5-F6] TRIG LPF | [F7-F8] PRESCALER: "+nf((pow(2, prescaler)),  1, 0)+" | [<--->] OFFSET", 25, 25);
71    text("frequency: "+nf(frequency,  5, 2)+"Hz"
72      +" | average DCV: "+nf(trigLevel/1024*voltageRange, 2, 2)+"V"
73      +" | samplerate: "+nf(sps, 5, 2)+"Hz"
74      +" | samples per line:  "+samplesPerLine
75      +" | division: "+samplesPerLine/sps*(float)width*100+"ms",  25, height-20);
76
77    // draw trigLevel (= average voltage) line
78    stroke(0,  0, 100);                                                                                   
79    int trigLevelHeight=(int)(trigLevel*(float)windowHeight/1024);
80    line(windowX,  windowY+windowHeight-trigLevelHeight, windowX+windowWidth, windowY+windowHeight-trigLevelHeight);  
81
82    // draw grid
83    stroke(50);                                                                                           
84    for (float n=0; n<=windowWidth; n+=(float)windowWidth/10) 
85      line(n+windowX,  windowY, n+windowX, windowHeight+windowY); 
86    for (float n=0; n<=windowHeight;  n+=(float)windowHeight/10) 
87      line(windowX, n+windowY, windowX+windowWidth,  n+windowY);
88
89    // ------------------------------
90    // DRAW WAVEFORM
91    // ------------------------------
92    stroke(255);
93    float prevSampleValue=0;
94    if (sync) readIndex=trigIndex;                               // sync: start  reading from last trig position
95    if (!sync) readIndex=writeIndex;                             //  no sync: start reading from last sample we received
96    readIndex+=offset;
97    float lineIncr=(float)1/samplesPerLine;
98    if (lineIncr<1) lineIncr=1;
99    for (float line=0; line<windowWidth; line+=lineIncr) {                                          //  cycle screen lines (from right to left)
100      float sampleValue=(float)getValueFromBuffer((int)((float)readIndex-line*samplesPerLine));     // get the value for the screen line
101      sampleValue*=(float)windowHeight/1024;                                                        // scale to windowHeight
102      if (line>0)
103        line(windowX+windowWidth-line, 
104        windowY+windowHeight-prevSampleValue,  
105        windowX+windowWidth-line-lineIncr, 
106        windowY+windowHeight-sampleValue);
107      prevSampleValue=sampleValue;
108    }
109
110    // ------------------------------
111    // BUFFER INCOMING BYTES & TRIG 
112    // ------------------------------
113    if (hold) {
114      serial.clear();                                                                                      //  HOLD: don't receive samples; clear serial buffer
115    }
116    else {
117      while  (serial.available ()>0) {                                                                      //  RUN: receive samples
118        writeIndex++;  
119        if (writeIndex>=bufferSize)  writeIndex=0;                                                          // handle  overflow
120        buffer[writeIndex+writeIndex]=(byte)serial.read();                                                 //  add 1 sample (2 bytes) to buffer 
121        buffer[writeIndex+writeIndex+1]=(byte)serial.read();
122        trigLevel=trigLevel*(1-trigLevelLPF)+(float)getValueFromBuffer(writeIndex)*trigLevelLPF;           // level for trigger intersection = exponential moving average of voltage
123        if (getValueFromBuffer(writeIndex)>=trigLevel&& getValueFromBuffer(writeIndex-1)<trigLevel)  {      // rising intersect detected
124          trigIndex=writeIndex;                                                                            //  set trigIndex (index of buffer that corresponds to last trig)
125          trigCounter++;                                                                                   //  count trigs (to calculate the frequency)
126        }
127      }
128    }
129  }
130}
131
132//  Read value from buffer
133int getValueFromBuffer(int index) {                                                                      
134  while (index<0) index+=bufferSize;                                                                       //  handle overflow of circular buffer
135  return((buffer[index*2]&3)<<8 | buffer[index*2+1]&0xff);                                                 // convert bytes to int
136}
137
138//  Handle keys
139void keyPressed() {  
140  if (key == CODED) {
141    if (connected)  {
142      if (keyCode == KeyEvent.VK_F1) {
143        samplesPerLine*=1.1;
144        if (samplesPerLine*windowWidth>bufferSize) samplesPerLine=bufferSize/windowWidth;
145      }
146      if (keyCode == KeyEvent.VK_F2) {
147        samplesPerLine/=1.1;
148        if (samplesPerLine<1/(float)windowWidth) samplesPerLine=1/(float)windowWidth;
149      }
150      if (keyCode == KeyEvent.VK_F3) {
151        sync=!sync;
152      }
153      if (keyCode == KeyEvent.VK_F4) {
154        hold=!hold;
155      }
156      if  (keyCode == KeyEvent.VK_F5) {
157        if (trigLevelLPF<.01) trigLevelLPF*=10;
158      }
159      if (keyCode == KeyEvent.VK_F6) {
160        if (trigLevelLPF>.000001)  trigLevelLPF/=10;
161      }
162      if (keyCode == KeyEvent.VK_F7) {
163        if  (prescaler>3) prescaler--;
164        serial.write((byte)prescaler);
165      }
166      if (keyCode == KeyEvent.VK_F8) {
167        if (prescaler<7) prescaler++;
168        serial.write((byte)prescaler);
169      }
170      if (keyCode == LEFT)  {
171        offset-=samplesPerLine*20;
172        if (offset<-bufferSize) offset=-bufferSize;
173      }
174      if (keyCode == RIGHT) {
175        offset+=samplesPerLine*20;
176        if (offset>0) offset=0;
177      }
178    }
179    else {
180      serial  = new Serial(this, Serial.list()[keyCode-112], serialBaudRate);
181      serial.write((byte)prescaler);
182      connected=true;
183    }
184  }
185}
186
187

import processing.serial.*;
import java.awt.event.KeyEvent;

//  Settings --------------------------------------------------------------------------
int  serialBaudRate=115200;
int bufferSize=10000000;      // number of samples (memory  use: 2 bytes per sample)
float samplesPerLine=1;       // increment 1 screen  line for each [n] samples
boolean sync=true;            // sync to trig
float  trigLevelLPF=.0001;     // trigLevel lowpass filter (exponential moving average)
boolean  hold=false;           // pause
int prescaler=5;              // ADC prescaler:  3:8 | 4:16 | 5:32 | 6:64 | 7:128
// -----------------------------------------------------------------------------------

Serial  serial;
PFont font= createFont("Lucida Console", 12, false);
byte[] buffer=  new byte[bufferSize*2];
int writeIndex, prevWriteIndex, readIndex, trigIndex,  trigCounter, loopCounter, windowWidth, windowHeight, offset;
float voltageRange,  sps, frequency, trigLevel, timer;
int windowX=30;
int windowY=50;
boolean  connected=false;
String serialPort;

void setup() {
  size(1000, 600);
  background(0, 0, 0);
  frame.setResizable(true);
  frameRate(50);    
  textFont(font);
  text("ARDUINO OSCILLOSCOPE\
\
Select serial port:", 25,  25);
  for (int i=0;i<Serial.list().length;i++)
    text("F"+(i+1)+" -  "+Serial.list()[i], 25, 80+i*20);
}

void draw() {
  windowWidth=width-100;
  windowHeight=height-100;

  if (connected) {
    background(0, 0, 0);
    
    // update frequency counters every second
    loopCounter++;
    if (loopCounter>frameRate) {  
      loopCounter=0;
      float elapsedSeconds=(millis()-timer)/1000;
      timer=millis();
      sps=(writeIndex-prevWriteIndex)/elapsedSeconds;  //  sample rate
      if (sps<0)sps+=bufferSize;
      prevWriteIndex=writeIndex;
      frequency=trigCounter/elapsedSeconds;            // signal frequency
      trigCounter=0;
    }

    // read switch position & set voltage range
    boolean switch1=((buffer[writeIndex*2]&(byte)8)==8);                                                 
    boolean switch2=((buffer[writeIndex*2]&(byte)4)==4);
    if (!switch1&&!switch2) voltageRange=20;
    if (!switch1&&switch2) voltageRange=10;
    if (switch1&&!switch2) voltageRange=6.64;
    if (switch1&&switch2) voltageRange=5;

    // print voltage scale
    for (int n=0; n<=10; n++)                                                                           
      text(nf(voltageRange/10*n, 2, 2)+"V", windowX+windowWidth+5, windowY+windowHeight-(n*windowHeight/10));

    // print interface and statistics
    text("[F1-F2] ZOOM | [F3] SYNC: "+sync+"  | [F4] HOLD: "+hold+" | [F5-F6] TRIG LPF | [F7-F8] PRESCALER: "+nf((pow(2, prescaler)),  1, 0)+" | [<--->] OFFSET", 25, 25);
    text("frequency: "+nf(frequency,  5, 2)+"Hz"
      +" | average DCV: "+nf(trigLevel/1024*voltageRange, 2, 2)+"V"
      +" | samplerate: "+nf(sps, 5, 2)+"Hz"
      +" | samples per line:  "+samplesPerLine
      +" | division: "+samplesPerLine/sps*(float)width*100+"ms",  25, height-20);

    // draw trigLevel (= average voltage) line
    stroke(0,  0, 100);                                                                                   
    int trigLevelHeight=(int)(trigLevel*(float)windowHeight/1024);
    line(windowX,  windowY+windowHeight-trigLevelHeight, windowX+windowWidth, windowY+windowHeight-trigLevelHeight);  

    // draw grid
    stroke(50);                                                                                           
    for (float n=0; n<=windowWidth; n+=(float)windowWidth/10) 
      line(n+windowX,  windowY, n+windowX, windowHeight+windowY); 
    for (float n=0; n<=windowHeight;  n+=(float)windowHeight/10) 
      line(windowX, n+windowY, windowX+windowWidth,  n+windowY);

    // ------------------------------
    // DRAW WAVEFORM
    // ------------------------------
    stroke(255);
    float prevSampleValue=0;
    if (sync) readIndex=trigIndex;                               // sync: start  reading from last trig position
    if (!sync) readIndex=writeIndex;                             //  no sync: start reading from last sample we received
    readIndex+=offset;
    float lineIncr=(float)1/samplesPerLine;
    if (lineIncr<1) lineIncr=1;
    for (float line=0; line<windowWidth; line+=lineIncr) {                                          //  cycle screen lines (from right to left)
      float sampleValue=(float)getValueFromBuffer((int)((float)readIndex-line*samplesPerLine));     // get the value for the screen line
      sampleValue*=(float)windowHeight/1024;                                                        // scale to windowHeight
      if (line>0)
        line(windowX+windowWidth-line, 
        windowY+windowHeight-prevSampleValue,  
        windowX+windowWidth-line-lineIncr, 
        windowY+windowHeight-sampleValue);
      prevSampleValue=sampleValue;
    }

    // ------------------------------
    // BUFFER INCOMING BYTES & TRIG 
    // ------------------------------
    if (hold) {
      serial.clear();                                                                                      //  HOLD: don't receive samples; clear serial buffer
    }
    else {
      while  (serial.available ()>0) {                                                                      //  RUN: receive samples
        writeIndex++;  
        if (writeIndex>=bufferSize)  writeIndex=0;                                                          // handle  overflow
        buffer[writeIndex+writeIndex]=(byte)serial.read();                                                 //  add 1 sample (2 bytes) to buffer 
        buffer[writeIndex+writeIndex+1]=(byte)serial.read();
        trigLevel=trigLevel*(1-trigLevelLPF)+(float)getValueFromBuffer(writeIndex)*trigLevelLPF;           // level for trigger intersection = exponential moving average of voltage
        if (getValueFromBuffer(writeIndex)>=trigLevel&& getValueFromBuffer(writeIndex-1)<trigLevel)  {      // rising intersect detected
          trigIndex=writeIndex;                                                                            //  set trigIndex (index of buffer that corresponds to last trig)
          trigCounter++;                                                                                   //  count trigs (to calculate the frequency)
        }
      }
    }
  }
}

//  Read value from buffer
int getValueFromBuffer(int index) {                                                                      
  while (index<0) index+=bufferSize;                                                                       //  handle overflow of circular buffer
  return((buffer[index*2]&3)<<8 | buffer[index*2+1]&0xff);                                                 // convert bytes to int
}

//  Handle keys
void keyPressed() {  
  if (key == CODED) {
    if (connected)  {
      if (keyCode == KeyEvent.VK_F1) {
        samplesPerLine*=1.1;
        if (samplesPerLine*windowWidth>bufferSize) samplesPerLine=bufferSize/windowWidth;
      }
      if (keyCode == KeyEvent.VK_F2) {
        samplesPerLine/=1.1;
        if (samplesPerLine<1/(float)windowWidth) samplesPerLine=1/(float)windowWidth;
      }
      if (keyCode == KeyEvent.VK_F3) {
        sync=!sync;
      }
      if (keyCode == KeyEvent.VK_F4) {
        hold=!hold;
      }
      if  (keyCode == KeyEvent.VK_F5) {
        if (trigLevelLPF<.01) trigLevelLPF*=10;
      }
      if (keyCode == KeyEvent.VK_F6) {
        if (trigLevelLPF>.000001)  trigLevelLPF/=10;
      }
      if (keyCode == KeyEvent.VK_F7) {
        if  (prescaler>3) prescaler--;
        serial.write((byte)prescaler);
      }
      if (keyCode == KeyEvent.VK_F8) {
        if (prescaler<7) prescaler++;
        serial.write((byte)prescaler);
      }
      if (keyCode == LEFT)  {
        offset-=samplesPerLine*20;
        if (offset<-bufferSize) offset=-bufferSize;
      }
      if (keyCode == RIGHT) {
        offset+=samplesPerLine*20;
        if (offset>0) offset=0;
      }
    }
    else {
      serial  = new Serial(this, Serial.list()[keyCode-112], serialBaudRate);
      serial.write((byte)prescaler);
      connected=true;
    }
  }
}

Downloadable files

Circiot

Comments

Only logged in users can leave comments

Ameduino

0 Followers

•

0 Projects

Intro